Question about 1991 Ford Thunderbird

1 Answer

Replace turn signal flasher - 1991 Ford Thunderbird

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

The flasher unit is located on the RH steering column opening reinforcement, and is attached by a bracket.

The combination turn signal and hazard flasher can be removed by pressing the plastic retaining clip (attached to the flasher housing) and pulling straight rearward. To install a new flasher, align the bracket with the track on the flasher housing. Then push the flasher forward until it snaps into the bracket.

Posted on Jun 04, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 599 Answers

SOURCE: turn signal flasher needs replaced

educated guess..flasher units (2) one for signals the other for emerg flashers usually located in fuse block under dash drivers side kick panel , glove box area ..or engine compartment near battery

Posted on Jan 13, 2009

  • 1 Answer

SOURCE: turn indicator sound (ticking) continues after signal is cancelled. replaced flasher and sound continues.

Remove the signal lever (switch) clean the grease completely and lube again with di-electric grease.
This should solve your problem.

Posted on May 30, 2009

ZJLimited
  • 17970 Answers

SOURCE: replace turn signal flasher. where is it located?

Underdash, in the driver side; review the Repair Manual ZJ-Secc-8W-Wiring-Diagrams (page 8, fig. 13)

I really hope helped with this (remember rated this help). Good luck.


Posted on Nov 10, 2009

jaxmortgage
  • 1 Answer

SOURCE: turn signal flashers do not work

I have the exact same problem. I replaced both underdash relays, checked all fuses and replaced the turn signal switch. Still no turn signals. Did you figure out what was wrong with yours?

Posted on Dec 27, 2009

  • 1 Answer

SOURCE: turn signals hazards flasher don't work jeep

I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Posted on Apr 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn lights blink with hazards but not with turn signal..flasher replaced. is It the multifunction lever then??


There should be a turn signal flasher and a hazard flasher. They are two different parts. If you replaced the hazard flasher and not the turn signal flasher than I would start by replacing the turn signal flasher.

One thing you can do once you find the turn signal flasher is to unplug it and use a jumper wire between the two pins of the connector then turn the key to the run position and place the turn signal lever in the left or right position. If the turn signal lights know light up than the turn signal flasher is the problem

Sep 09, 2014 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Turn signals & Flashers will not work on 2002 Dodge Dakota, replaced Combination Flasher unit, still no turn signal or Flasher


Hi Jeff , do you know how to test electrical circuits using a DVOM - digital volt ohm meter ? How to read an use a wiring diagram to pin point testing points in the turn signal circuits ? Here is a web site for free wiring diagrams http://www.bbbind.com/free_tsb.html .Enter vehicle info year ,make , model an engine size . Under system click on lighting ,then under subsystem click on turn signal lamp , Click the search button then the blue link . Then watch this videos an then test the power and grounds ,inputs to the Combination Flasher !
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
How to Use Multimeter to Troubleshoot Common Problems
The Trainer 18 Electrical Testing Tips


Jul 03, 2017 | Cars & Trucks

1 Answer

Turn signals were working...but blinking fast. now they don't work at all...replaced fuse in side panel near door and still nothing. Everything else works..headlights, wipers, hazards..what gives?


you have a separate flasher for the turn signals.this is what your problem sounds like.if all your lights are working including the signal indicator on the dash then it will be the signal flasher.if you turn on the hazard flashers and locate it under the dash, this will show you what the turn signal flasher will look like.then you will have to look for the flasher unit on the fuse panel that looks like the hazard flasher.replace the turn signal flasher and you will have your signal flashers again

Mar 08, 2011 | 1996 Dodge Ram 1500 Club Cab

2 Answers

Turn signals won't flash. They do come on but no intermittant flashing. Flasher has been swapped out. All turn signal lights come on on both sides front and back.


i think you may have replaced the hazard flasher not the turn signal flasher, the turn signal flasher is located behind the dash on the right side of the steering collum support, the hazard flasher is located in the convenience center.

Jan 14, 2011 | 1995 Chevrolet Cavalier

2 Answers

My passenger side turn signal blinks double time, what do i need to do to fix it?


Check that the bulbs are lighting and if they don't replace as needed. If they are fine the turn signal flasher is bad. Replace the flasher and the problem is fixed. If you have to replace the flasher the easy way to find it is turn your turn signal on on listen for the clicking . Find the clicking and you found your flasher.

Nov 08, 2009 | 2002 Volkswagen Passat

1 Answer

Turn signal flashers do not work. have replaced bulbs, two flasher units found on fire wall. one round one square. both operate hazards. can't find turn signal flasher. even looked behind instrument panel....


I have the exact same problem. I replaced both underdash relays, checked all fuses and replaced the turn signal switch. Still no turn signals. Did you figure out what was wrong with yours?

Oct 31, 2009 | 1995 Chevrolet Cavalier

1 Answer

2000 Intrepid turn signals stopped working, I replace the flasher relay, still turn signals not working?


did you replace the turn signal flasher or the emergency flasher? turn on the emergency flasher lights and pull that flasher if they quit working you changed the wrong one.

Jun 25, 2009 | 2000 Dodge Intrepid

2 Answers

97 honda accord turn signal problem


Flasher unit is bad. Replace flasher

Dec 28, 2008 | 1997 Honda Accord

3 Answers

Turn signals


replaced turn signal flashers and muti switch turn signal still won't work Why?

Nov 08, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1991 Ford Thunderbird Logo

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...