Question about 1991 Ford Bronco

1 Answer

How to replace an exaust manifold on a 1991 ford bronco 302-v8

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Start by removing nuts from exhaust pipe on the underside, then remove the 8 bolts that hold manifold to engine and pull it up. make sure when reinstalling you inspect the gasket and replace if needed. there is also a circular gasket between the exhaust manifold and the exhaust pipe, inspect and replace if needed. reverse for install.

Posted on Aug 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump on 1990 ford bronco 302 V8 5.0 liter


Under the Hood.

You can find the exact one on

www.bbbind.com and put your Exact car in for the Location

Apr 12, 2013 | 1990 Ford Bronco

1 Answer

Could i replace my 351 windsor with a 302 in 1991 bronco


what are you going to do with the old 351 windsor does it run i happen to be looking for one

May 24, 2012 | 1991 Ford Bronco

1 Answer

What is the spark plug firing order for a 1989 Ford Bronco with a 302 Cu. In. V8 engine?


There are three kinds of 302s made from 1982-2001. 5.0L HO This engine was used in 1983-1995 Mustangs, Mark VII Lincolns, and some T-birds and Cougars. All Explorer 5.0L engines are 5.0L HO engines as well. They use the 351W firing order, 1-3-7-2-6-5-4-8. Except for the 1983-84 Mustangs, all of these engines are roller cam equipped. They use a reverse rotation water pump and front cover. The 1994-5 Mustang and all Explorers use a unique front cover and water pump. 5.0L Full Size Car This engine was used in 1982-1990 Crown Victoria and Grand Marquis. They use the 289-302 firing order, 1-5-4-2-6-3-7-8. Most of these cars are not roller cam equipped, however sometime in the early 1990s they started using roller cams but retained the 302 firing order. They use a standard (clockwise) rotation water pump and front cover. 5.0L Truck (except Explorer) These engines are similar to the Full Size Car engines, except they use different intake manifolds and camshaft profiles. They also use the 289-302 firing order, 1-5-4-2-6-3-7-8. They also began using roller cams sometime in the early 1990s. They use a reverse rotation water pump and front cover.

Good Luck

Nov 12, 2010 | 1989 Ford Bronco

1 Answer

Where is the back up light switch located in the engine compartment for a 1991 Ford Bronco XLT with a 302 V8?


The back up light switch is located on the transmission, left side, it is the trange selector switch as well. Hope this helps, Let mw know.

Jul 05, 2010 | 1991 Ford Bronco

1 Answer

Did ford make a 6 cylinder engine for the 1985 ltd ? i need an exaust pipe,but all i can find is for a 302 v8. thanks


They made a 4 cylinder 2.3Liter,V-6 3.8Liter and the V-8 5.0Liter so yours if it is a 6 cylinder it would be the 3.8Liter

Apr 08, 2010 | 1985 Ford LTD

1 Answer

302 v8 on a 76 ford bronco just rebuilt has


sounds like your timing is way off,if no timing gun and you dont have specs,loosen your distributer a bit and rev your engine to about3000 rpm and just listen to the engine while you slightly turn the distibuter until it is the smoothest sounding with no sputtering then tighten your distributer back up or pay the bucks get it timed at a shop its cheap

Oct 19, 2009 | 1981 Ford Bronco

1 Answer

Where is the thermostat located on a 1991 ford bronco fullsize with a 5 liter 302 cubic inch engine


follow the upper radiator hose to the engine it is behind the housing that the hose is clamped on, two 13mm bolts hold it on

Aug 03, 2009 | 1991 Ford Bronco

1 Answer

Where can i find side exaust for my 83 for mustang?


Get on the internet and go to Jeggs or Summitt and you will find all kinds of aftermarket suppliers for the exhaust. Or, just go to Gibson Exhaust or Borla. They all have these kits. They are not cheap though.

Feb 26, 2009 | 1983 Ford Mustang Hatchback

Not finding what you are looking for?
1991 Ford Bronco Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...