Question about 1997 Land Rover Range Rover

1 Answer

R reg Range Rover, There is a delayed response when accelerating from a standing start, then after a couple of seconds and a buried accelerator pedal it flies. Also, tick over seems very high. Any ideas on a possible solution?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 766 Answers

I would change your throttle position sensor (TPS) or at least check all related wiring, fuses and relays concerning this device. It is located on the outside of the throttle body at the end of the throttle plate shaft. Its function is to send a an electrical signal to the ECU that correspnds to the position of the throttle plate. Your TPS is not sending a signal to the ECU so the ECU does not know to inject more fuel in response to the throttle being opened. The call for more fuel in the absence of immediate input from the TPS is being made to the ECU by the Manifold air pressure sensor but this can a take a second or two to respond to pressure changes, hence the hesitation in acceleration. One really quick way to check is to simply disconnect the TPS electrical connector. If it were running normally you will notice an immediate change in engine idle, as your is faulty you will notice no difference

Posted on Jun 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dtc p0121 throttle position (tp) sensor performance


code p 0121 has to answers
1--refers to throttle position (TP) sensor/accelerator pedal position sensor A--range /performance problem====causes --accelerator cable adjustment--TP/APP sensor ---wiring
The second reference is the same and the causes are--accelerator cable adjustment--TP/APP switch
(APP is accelerator pedal position)

Aug 30, 2016 | Cars & Trucks

Tip

How to reset ECU,Throttle and Accelerator Position Learning


Hi.

Below the procedure to reset ECU,Throttle and to perform Accelerator Position Learning on Nissan. It works on Titan, Altima, Infinity, pathfinder and other models.

ECU Resetting


While performing the procedures below, ensue that you are respecting the times stated. If the steps are not done within the specified times, the module will not reset. You will need to use a watch or a chronograph while performing the procedures.

Procedure:

1. Ensure that the accelerator pedal is fully released, set ignition switch to the “ON” position, then wait 3 seconds.
2. Follow the steps a and b below, repeat the two steps in sequence quickly for five times within 5 seconds.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal in full.
3. Wait 7 seconds, then depress the accelerator pedal completely, and hold it for about 10 seconds until the CEL (check engine light) starts blinking.
4. Release the accelerator pedal while the CEL is still blinking.
5. Wait 10 second.
6. Depressthe accelerator pedal in full and hold it for 10 seconds or more.
7. Fully release the accelerator pedal while the CEL light keeps flashing.
8. Turn the ignition switch to “OFF” position and start the vehicle. If procedure has been done correctly, then the light light will turn off.
If the light continues to stay on, repeat the procedure.

Accelerator Pedal Release Position Learning

Procedure

1. Ensure that the accelerator pedal is completely released before starting the procedure.
2. Turn the ignition switch “ON” and wait at least 2 seconds.
3. Turn the ignition switch “OFF”, and wait at least 10 seconds.
4. Turn the ignition switch “ON” and wait 2 seconds.
5. Turn the ignition switch “OFF” and wait 10 seconds.

Throttle Valve Closed Position Learning

Procedure

1. Ensure that accelerator pedal is completely released.
2. Turn ignition switch to the “ON” position.
3. Turn ignition switch to the “OFF” position and wait at least 10 seconds.
Ensure that the throttle valve moves after turning the switch off.

Idle Air Volume Learning (Throttle Position Learning)

Procedure

1. Follow the Accelerator Pedal Released Position Learning described above.
2. Do the Throttle Valve Closed Position Learning also described above.
3. Start the engine, and allow warming up.
4. Turn the ignition on “OFF” positionand wait 10 seconds.
5. Ensure that accelerator pedal is fully released, then turn the ignition switch to “ON” position, and wait 3 seconds.
6. Repeat the steps a and b below five times within 5 seconds in sequence.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal until reaching full extension.
8. Wait 7 seconds or more, depress the accelerator pedal completely and hold the pedal down for about 20 seconds until you see that the Check Engine Light stops blinking and starts getting steady..
9. Rrelease completely the accelerator pedal within 3 seconds after the light coming ON.
10. Start engine and let it run at idle for about 20 seconds.
12. Test the engine to ensure the idle speed and ignition timing are set correctly.

Regards.

on Mar 25, 2010 | Nissan Titan Cars & Trucks

1 Answer

When accelerate above 30mph its cuts out or loses power but runs smooth at idle


Acceleration cut off when reach 30mph - Range Rovers

www.rangerovers.net/...rover.../27680-acceleration-cut-off-when-reach-...

Mar 30, 2010 - 16 posts - ‎6 authors
All of a sudden, RRSport HSE 2006 can not speed above 30mph. ... It's only an hour's drive away if your car could go straight upwards. .... My guess is that some control module got fried or out of whack when the power spike ...

WILL NOT GO OVER 30MPH WITH PEDLE TO METAL ...

repairpal.com > Questions > Dodge > Charger > 2006 Dodge Charger
... and a 18 wheeler comes up behind me going 85mph. or more and my car drops down to 35 to 40. ... It would not let me go pass 30mph and it would bog out. .... His truck was barely over 36k. when this happened. ... sudden I was cruising at 30 more or less and could not accelerate or shift gears I could just switch to Drive.

My Chevy Silverado won't go over 25 miles an ... - CarGurus

www.cargurus.com > Questions > Chevrolet > Silverado 1500

CarGurusSep 19, 2012 - His response wasn't even there until the page refreshed when I hit ...The engine would shut off due to a clogged fuel filter not hit 25 MPH and just stopaccelerating. ... when the gas pedal was to the floor but it wouldn't go over 30 MPH?.... When I punch it at 110 or above, it will cut out and drop to 103kph, ...

Starts,Idols perfect Bogs down, no power upon acceleration ...


Jan 31, 2016 | Cars & Trucks

1 Answer

MY 2010 CHRYSLER TOWN AND COUNTRY TAKES A SLOW RESPONSE BEFORE TALKING OFF. I PUT MY FOOT ALL THE WAY DOWN BUT IT DELAY A COUPLE OF SECONDS BEFORE ACCELERATING


That is a drive by wire throttle set up. (No cable connects the pedal to the throttle body) I have heard of a few problems with throttle body motor lag, but i would check the pedal sensor and see if it is within the specs and do the same for the motor.

Nov 04, 2013 | Cars & Trucks

1 Answer

Range rover 2.5D P38A model. Loss of accelerator


Give me some more information about this problem. May be i can help.

Jul 12, 2011 | 1996 Land Rover Range Rover

1 Answer

Pinging while accelerating range rover. I have no idea what it is.. Car runs fine. Pinging starts when i push down on the accelerator.


What grade of fuel are you using? Some Rovers call for premium grade. If you are not using premium I would suggest giving it a try.

Apr 11, 2011 | 1997 Land Rover Range Rover

2 Answers

Sometime no accelerator response


YOUR ACCELERATOR PEDAL SENSOR ON ACCELERATOR PEDAL IT HAS BOLTS HOLDING IT IN PLACE.JUST UNPLUG ACCELERATOR CONNECTOR AND REMOVE THE BOLTS THEN SENSOR.

Jun 06, 2010 | 2002 Ford F350 Super Duty DRW Reg. Cab

4 Answers

1995 Range Rover Land Rover Questions


the back windshield is the front windshield one just pull it front or back not up all down
hope is helps
Jamie

Oct 05, 2008 | 2004 Land Rover Range Rover

Not finding what you are looking for?
1997 Land Rover Range Rover Logo

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...