Question about 2003 Pontiac Grand Prix

1 Answer

Is the retaining bolt on the harmonic balancer for a '94 toyota camry reverse threaded

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

No. It loosens, turning counter-clockwise.

Posted on Jun 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install balance drive gear on crankshaft 2007 Camry 2.4


Remove old crankshaft pulley ( Harmonic Balancer), by putting sturdy socket,think its 19mm, or 3/4 " on the center crankshaft bolt, with a good size breaker bar, wedge the breaker bar in between the suspension, and drive axle, to keep the breaker bar from spinning, while, you now turn the key inside the car, to engage starter, to spin the crankshaft,which may take several attempts, of turning the key, and putting socket back on, they are very stubborn,to break the center bolt loose,
Then remove harmonic balancer, with a PULLER, which requires 2 bolts, in the threaded holes, one on each side of the now empty center bolt hole, autozone , advance, has these to loan out, only requires deposit, which they give back to you, when you return it.
Put square key in slot on bare crankshaft, slide harmonic balancer,(crankshaft pulley,while lining up the square key,and tighten crankshaft bolt.

Oct 24, 2014 | 2007 Toyota Camry

1 Answer

How to replace crankpully on 3300 olbs


The harmonic balancer on these engines is now press fit onto the crankshaft and requires the use of Tool J-38197 for removal. The torque specification to be used during installation has also been revised. The procedure to be used when replacing the crank sensor is as follows:

REMOVAL






  1. Disconnect serpentine belt from crankshaft pulley.


  2. Raise vehicle on hoist.


  3. Remove right front tire and wheel assembly.


  4. Remove right inner fender access cover.


  5. Using 28 mm socket, remove crankshaft harmonic balancer retaining bolt.


  6. Remove crankshaft harmonic balancer using Tool (J-38197).


  7. Remove foreign object deflector (DO NOT use pry bar).


  8. Disconnect sensor electrical connector.


  9. Remove sensor and pedestal from block face.


  10. Remove sensor from pedestal




INSTALLATION






  1. Loosely install crankshaft sensor on pedestal.


  2. Position sensor with pedestal attached on Tool J-37089.


  3. Position tool on crankshaft.


  4. Install bolts to hold pedestal to block face, torque to (18-26 lb. ft.).


  5. Torque pedestal pinch bolt to (26-44 lbs. in.).


  6. Remove Tool J-37089.


  7. Install foreign object deflector.


  8. Place Tool J-37089 on harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.


  9. Install balancer on crankshaft.


  10. Apply thread sealer GM #(NNN) NNN-NNNNor equivalent to threads of crankshaft balancer bolt. Torque bolt to + 56 degrees (104 lb. ft. + 56 degrees).


  11. Install inner fender shield.


  12. Install tire and wheel assembly. Torque lug nuts to (104 lb. ft.).


  13. Lower vehicle.


  14. Install serpentine belt.
see this vedio

Jul 11, 2014 | 1993 Oldsmobile Cutlass Ciera

3 Answers

How do you remove the harmonic balancer on a 1987 GMC R3500 with a 454?


You remove the giant bolt, then you use a harmonic balancer puller, which essentially bolts up rather than using claws to grab. The bolts of the puller go into the pulley fastening bolt holes.

Something must happen to protect the crank threads, a spacer, using the retainer bolt, or whatever, just do not kill the threads.

Feb 25, 2011 | 1987 GMC R3500

1 Answer

I need to replace crank shaft timing sensor


  1. Disconnect the negative battery cable.
  2. Disconnect the electrical connector at the sensor.
  3. Using a 28mm socket and pull handle, rotate the harmonic balancer until any window in the interrupter is aligned with the crank sensor.
  4. Loosen the pinch bolt on the sensor pedestal until the sensor is free to slide.
  5. Remove the pedestal to the engine mounting bolts.
  6. While manipulating the sensor within the pedestal, carefully remove the sensor and pedestal as a unit. To install:
  7. Loosen the pinch bolt on the new sensor pedestal until the sensor is free to slide.
  8. Verify that the window in the interrupter is still in the correct place.
  9. Install the sensor and pedestal as a unit while making sure that the interrupter ring is aligned within the proper slot.
  10. Install the pedestal and tighten the engine mounting bolts to 22 ft. lbs. (30 Nm).
3X Sensor
  1. Disconnect the negative battery cable.
  2. Remove the sensor harness connection to the sensor. Fig. 1: Unsecure the harness, then unfasten the bolt to remove the CKP sensor 86815102.gif

  3. Unsecure the sensor block bolt.
  4. Remove the Crankshaft Position (CKP) sensor from the vehicle. Inspect the O-ring for cracks and replace if needed. To install:
  5. Install the new O-ring if needed and lubricate with engine oil.
  6. Install the sensor into the hole in the block.
  7. Install the mounting screw and tighten to 71-88 inch lbs. (8-10 Nm).
  8. Attach the sensor harness connector, then connect the negative battery cable.
Dual Crank Sensor Sections 3 and 4 of this manual also cover testing, removal and installation, and adjustment of many computer controlled components.
  1. Disconnect the negative battery cable.
  2. Remove the belt(s) from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Remove the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer.
  6. Disconnect the sensor electrical connector.
  7. Remove the sensor and pedestal from the engine block, then separate the sensor from the pedestal. To install:
  8. Loosely install the crankshaft sensor to the pedestal.
  9. Using tool J-37089 or equivalent, position the sensor with the pedestal attached, on the crankshaft.
  10. Install the pedestal-to-block retaining bolts. Tighten to 14-28 ft. lbs. (20-40 Nm).
  11. Tighten the pedestal pinch bolt 30-35 inch lbs. (3-4 Nm).
  12. Remove tool J-37089 or equivalent.
  13. Place tool J-37089 or equivalent, on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly. NOTE: A clearance of 0.025 in. (0.635mm) is required on either side of the interrupter ring. Be certain to obtain the correct clearance. Failure to do so will damage the sensor. A misadjusted sensor of bent interrupter ring could cause rubbing of the sensor, resulting in potential driveability problems, such as rough idle, poor performance, or a no-start condition.
  14. Install the balancer on the crankshaft. Install the balancer retaining bolt. Tighten the retaining bolt to 200-239 ft. lbs. (270-325 Nm).
  15. Install the inner fender shield.
  16. Install the right front wheel assembly. Tighten the wheel nuts to 100 ft. lbs. (136 Nm).
  17. Lower the vehicle.
  18. Install the belt(s).
  19. Reconnect the negative battery cable.
24X Crank Sensor
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer.
  5. Disconnect the sensor electrical connector.
  6. Unfasten the sensor bolts, then remove the sensor. Fig. 2: The 24X crankshaft sensor is secured by two bolts 86815103.gif
    To install:
  7. Install the crankshaft sensor to the engine with the two mounting bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  8. Attach the electrical harness to the sensor.
  9. Using tool J-29113 or equivalent, install the harmonic balancer to the vehicle.
  10. Apply a thread sealer such as GM 1052080 or an equivalent to the threads if the crankshaft balancer bolt, then tighten the bolt to 110 ft. lbs. (150 Nm).
  11. Lower the vehicle.
  12. Install the serpentine belt.
  13. Reconnect the negative battery cable.

Dec 16, 2010 | 2003 Buick Rendezvous

1 Answer

What side of the block is the crankshaft positioning sensor located on a 1993 olds cutlas supreme?


prev.gif next.gif REMOVAL & INSTALLATION Fig. 1: Crankshaft Position (CKP) sensor mounting 88004g85.gif
Fig. 2: The 24X CKP sensor is mounted to the engine front cover - 3.1L (VIN M) engine 88004g89.gif
2.2L, 2.3L, 3.1L (VIN T and V) and 1991-93 3.4L Engines
  1. Disconnect the negative battery cable.
  2. Detach the sensor harness connector from the sensor.
  3. Unfasten the sensor retaining bolts, then remove the sensor from the engine.
  4. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  5. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  6. Install the sensor retaining bolt. Tighten to 88 inch lbs. (10 Nm).
  7. Attach the sensor harness connector.
  8. Connect the negative battery cable.
2.5L Engine
  1. Disconnect the negative battery cable.
  2. Remove the DIS assembly, as outlined in Section 2 of this manual.
  3. Remove the sensor retaining screws and remove the sensor from DIS assembly.
  4. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  5. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor.
  6. Fit the sensor to the DIS assembly and install the retaining screws. Tighten the retaining screws to 20 inch lbs. (2.3 Nm).
  7. Install the DIS assembly to the engine, as outlined in Section 2 of this manual.
  8. Connect the negative battery cable.
3.1L (VIN M) Engines 3X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Turn the steering wheel to the full left position.
  3. Raise and safely support the vehicle.
  4. Detach the sensor harness connector from the sensor.
  5. Unfasten the sensor retaining bolts, then remove the sensor from the engine.
  6. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  7. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  8. Install the sensor retaining bolt. Tighten to 71 inch lbs. (8 Nm).
  9. Attach the sensor harness connector.
  10. Carefully lower the vehicle.
  11. Turn the steering wheel to the straight ahead position, then connect the negative battery cable.
24X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. If necessary for access, remove the right front wheel and inner fender access cover.
  5. Unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 24420-B.
  6. Detach the sensor electrical connector.
  7. Unfasten the sensor retaining bolts, then remove the sensor from the vehicle. To install:
  8. Install the CKP sensor and secure using the retaining bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  9. Attach the sensor electrical connector.
  10. Install the balancer on the crankshaft using special tool J 29113, or equivalent.
  11. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  12. If removed, install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  13. Carefully lower the vehicle.
  14. Install the serpentine belt.
  15. Connect the negative battery cable.
1994-96 3.4L Engine 3X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the intermediate exhaust pipe.
  4. Remove the rack and pinion heat shield.
  5. Remove the alternator cooling duct.
  6. Detach the sensor electric connector.
  7. Remove the 3X CKP sensor from the engine.
  8. Inspect the sensor O-ring for damage, and replace, if necessary. To install:
  9. If necessary, lubricate a new O-ring with clean engine oil and install on the sensor. Install the sensor into the engine.
  10. Install the sensor-to-block bolt and tighten to 71 inch lbs. (8 Nm).
  11. Attach the sensor connector.
  12. Install the alternator cooling duct.
  13. Install the rack and pinion heat shield.
  14. Install the intermediate exhaust pipe.
  15. Connect the negative battery cable.
24X CRANKSHAFT POSITION (CKP) SENSOR
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 38197, or equivalent.
  6. Detach the sensor electrical connector.
  7. Unfasten the sensor retaining bolts, then remove the sensor from the vehicle. To install:
  8. Install the CKP sensor and secure using the retaining bolts. Tighten the bolts to 8 ft. lbs. (10 Nm).
  9. Attach the sensor electrical connector.
  10. Install the balancer on the crankshaft.
  11. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm).
  12. If removed, install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  13. Carefully lower the vehicle.
  14. Install the serpentine belt.
  15. Connect the negative battery cable.
3.8L Engine
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the crankshaft pulley.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel and inner fender access cover.
  5. Using a 28mm socket, unfasten the crankshaft harmonic balancer retaining bolt, then remove the harmonic balancer using tool J 38197, or equivalent.
  6. Remove the CKP sensor shield. Do NOT use a prybar to remove the shield!
  7. Detach the sensor electrical connector.
  8. Unfasten the sensor retaining bolts, then remove the sensor from the block face. To install:
  9. Position the CKP sensor to the block face, then secure using the retaining bolts. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  10. Install the CKP sensor shield.
  11. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Apply thread sealer 1052080 or equivalent to the bolt threads of the crankshaft balancer bolt. Tighten the bolt to 110 ft. lbs. (150 Nm), plus an additional 76°turn.
  14. Install the inner fender shield and the right front wheel and tire assembly. Tighten the wheel lug nuts to 100 ft. lbs. (140 Nm).
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Nov 12, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Harmonic balancer retaining bolt is off, but i can only get two of the three puller bolts to thread. How do i remove it?


RETAP THIRD HOLE ONE SIZE UP ARE IF IT IS SAE THEN USE METRIC I HAVE WENT COURSE THREADED BOLT ALITTLE BIGGER JUST SO IT GETS A BITE.

Feb 13, 2010 | 2000 Pontiac Grand Prix

1 Answer

Is the harmonic balancer on with reverse threading


it is right hand thread,but very tight. torque spec is 87 ft.lbs.use a 1/2 '' drive breaker bar,with parking brake applied,in park w/ auto trans,in gear w/ a manual transmission.

Oct 11, 2009 | 1991 Toyota Camry

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

1 Answer

Toyota camry


It should be right hand threads.
fh

Jul 25, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
2003 Pontiac Grand Prix Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...