Question about 1987 Toyota Supra

1 Answer

1986.5 toyota supra turn signal does not flash when in the detent only flash when partially hold down, replace flasher no help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 65 Answers

Do thr break lights work? sometimes people put the blinker bulbs in reversed and cause the low element to flash which will not be seen over the high element..oh and congrats on having the beast.im an evo owner

Posted on Jun 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 toyota celica st turn signal relay location


1986 Toyota Celica 2.0L FI 4cyl

The Flasher is located: Front seating area, driver side, under dash, mounted driver side of steering column. here's a link showing what it look's like. GET 35 GIFT CARD FOR EVERY 100 SPENT ON ONLINE SHIP TO HOME ORDERS Here's a new one Timbo. http://www.autozone.com/electrical-and-lighting/turn-signal-flasher/novita-turn-signal-flasher/toyota/celica/1986/4-cylinders-s-2-0l-fi/511475_0_11714

Aug 14, 2015 | Toyota Cars & Trucks

2 Answers

Turn signal flashes fast but bulbs good


Under the dashboard there is a round metal device called a flasher its where the tick noise comes from when you activate your turn signal I would try replacing that next Good luck

Apr 04, 2014 | Toyota Camry Cars & Trucks

1 Answer

1986 oldsmobile cutlass turn signal not working anymore...emergency flashers work brake lights work just not turn signals


OMG. Someone with a car older than my '87 toyota. Possibly a bad switch, but first locate your turn flasher, maybe that is bad, easier to try than another switch. Turns should have a fuse, too. check that.

Oct 30, 2011 | 1986 Oldsmobile Cutlass Supreme

2 Answers

When putting on the left or right turn signal or flashers the two front lights do not flash. Also noticed that as the rear flash, it is faster than normal.


sounds like a bad bulb or flasher...
If the light outside light up , but do not flash.... then plink the flasher ( round silver bulb in the fuse box) with a finger and see if they start working...

Sep 24, 2010 | 2004 Toyota 4Runner

1 Answer

Signal lights do not flash when using turn


There are two flashers. One for the hazards and one for the turn. Try switching around the flashers

Apr 12, 2010 | Toyota Tacoma Cars & Trucks

2 Answers

2000 toyota camry turn signals not working. Fuses check out and bulbs good.


Hi, i recommend testing the switch and flasher module. i will post the testing procedures for both devices. replace the device that is faulty.

To test turn signal switches, use a 12-volt test light to probe for voltage into and out of the switch. The ignition switch must be in the RUN position for the circuit to operate. If voltage is present on the input side of the switch but not on the output side, the switch is faulty.

FLASHER TEST PROCEDURE---
  • A test light can be used to determine which flasher is used for the turn signals and which is used for the hazard warning light.
  • An easier way is to turn on both the directionals and the hazards. This activates both flasher units.
  • By removing one of the flashers, the affected circuit no longer flashes.
  • Therefore, that flash unit controls that particular circuit.
  • If the turn signals fail to operate and the fuse is good, the flasher has probably failed.
  • Occasionally, the flasher does not flash as fast as it once did, or it flashes faster. This is also cause for replacement.
  • If it flashes too slowly or not at all, check for a burned-out bulb first.
the flasher is located in the Front seating area, driver side, driver side of steering column, mounted in corner behind instrument panel

If the turn signals operate properly in one direction but do not flash in the other, the problem is not in the flasher unit. A burned-out lamp filament will not cause enough current to flow to heat the bimetallic strip sufficiently to cause it to open. Thus the lights do not flash. Locate the faulty bulb and replace it.

May 19, 2009 | 2000 Toyota Camry

1 Answer

2001 Ford Ranger right turn signal doesn't work when the braking


Flasher Unit sounds bad... change the flasher, which is in the inboard fuse panel.

Feb 27, 2009 | 1986 Ford Ranger 2WD

1 Answer

No brake lights of blinkers 1990 dodge dynasty


While not likely, it is possible that the light bulbs in both sides are have bad filaments. Turn on ignition key (but don't start engine). Then turn on parking lamps (first detent or "click" on headlamp switch). Walk around car and look for illumination on front parking lamps and rear tail lights. Turn on the right turn signal. Are those (right hand) lamps now changing brilliance? Try the left turn signal in the same manner. Are those (left hand) front and rear lights changing briiliance? Take note of any positions that did NOT change briliance when the turn signals were activated. If NONE changed briliance, you either have a bunch of bad bulbs (unlikely) or a bad flasher (more likely) or a bad turn signal switch (most likely) or perhaps wiring problems (possible if the car has been in a collision or has been "worked on" by some "non-expert" mechanic). Check the action of the emergency flasher control switch located on the steering column (facing up). Pushing it in (down) should result in the button going to two different heights alternately (low, high, low, high). You could just have bad flashers or corroded flasher contacts! Good luck!

Nov 15, 2008 | 1993 Dodge Dynasty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...