Question about 2001 Suzuki Xl 7

Open Question

How to replace rear wheel bearing for suzuki xl7

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
ewashmidas
  • 362 Answers

SOURCE: Rear wheel bearings for my 1988 Suzuki Samurai

They are pressed in, not an easy job.

Posted on Feb 11, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is a noise coming from the rear end of my 2006 suzuki grand vitara


Hi, The Suzuki Grand Vitara is a superb vehicle, several reasons can be applied to rear end noise.

Most are not expensive or difficult to repair. However a few can be expensive.
Lets look at the most common, wheel bearings, are the usual component to wear and require replacement, if it is a wheel bearing, its much better to have both wheel bearings replaced.

A wheel bearing will become noisy at certain speeds and give of a distinctive noise, best noticed on a flat road.
However a repair shop can easy diagnose a wheel bearing for you.
Other problems could be found within the differential back axle, this can again be easily diagnosed by the engineer looking for a wheel bearing fault.

I hope this proves to be helpful

Adam

Jan 14, 2018 | Suzuki Cars & Trucks

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

2 Answers

How do you replace rear wheel hub assembly on 2008 suzuki xl7?


hub? what is a hub? the axle? what is bad, post bad first then ask questions.
alldata.com

or the FSM
or
only, 4$ bucks to look

https://suzukipitstopplus.com/Products/1158-2008-xl7-service-manual.aspx

Jul 25, 2014 | 2007 Suzuki XL-7

1 Answer

Front wheel bearing on suzuki 03 xl7 4x4


old post.
and axles , really?
RTM

https://suzukipitstopplus.com/Products/1064-2005-forenza-reno-service-manual.aspx

$4 bucks to read the manual.
such a deal .

here is the GV , page. its same really
http://www.fixkick.com/hubs/vitara/new-vit-hubs.pdf

2001 + have the newer bearing hubs, unitized.
http://www.fixkick.com/hubs/no-crush.JPG


removing is easy, putting back right far harder.

see end hub #4
pull that with slide hammer, after removing screws #6
remove 7,8,9 and then using special tool pull ring 11.
with slide hammer pull, bearing hub.#1

RTM read the manual , at pitstop above
or the factory service manual , FSM
or at alldata.com,

Dec 31, 2013 | 2003 Suzuki XL-7

1 Answer

Remove front left wheel bearing and axle


alldata.com

or rear FSM>
here is the discount link,. log in , its al there.

http://www.scantool.net/software/alldata-diy-1-month-subscription.html


the real book, is used at fleabay

Dec 31, 2013 | Suzuki Cars & Trucks

1 Answer

2003 SUZUKI XL7 2wd v6 \r\nRear wheel bearing making noise. How do you know for sure that is the problem and is bearings all i need I have ABS. How do I remove the bearing or the hub if that is what I...


remove the wheel and firmly hold the hub that encloses the wheel bearing. Now see if you can rock the hub
If so the bearing is bad
You will need to remove the braking system first to gain access to remove the hub assembly
the bolts are on the back side which is 3 of them

May 22, 2011 | 2003 Suzuki XL-7

2 Answers

Replacing wheel bearings on suzuki swift


Front or rear?? Big diff! Frankster016

Oct 26, 2008 | 1996 Suzuki Swift

1 Answer

Power steering rack 2003 suzuki xl7 leaks


i get a sort of grating squeal coming right front wheel when turning right. i've checked the wheel bearings and there ok. it only seems to happen when moving above 15 mph. any idea's what this could be?

Aug 13, 2008 | 1997 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

610 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...