Question about 2001 Hyundai XG300

1 Answer

What is the proper air pressure for the low side port of the air conditioning system in a hyundai xg300?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 6,826 Answers

32 psi to about 37 psi at idle.

Posted on Jun 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 hyundai xg300 oil light comes on


Did you check your oil? If it is low you need to add some.

Check oil light could mean either low oil volume (low on oil) or your oil sending unit is not pumping oil or that you have some much gunk build up that your oil ports have clogged up.

Jul 01, 2011 | 2001 Hyundai XG300

Tip

Air conditioning


When an vehicle's air conditioning system has not been used for several months, the seals within the system start getting dry. I've never worked on a Peugeot 206 or any other peugeot before, that's why I had no idea where the low pressure ac port was. The high pressure ac port is the easiest to locate, because it is in the engine compartment, facing the car from the front, on left side of the radiator. The low pressure ac port is in the engine compartment, facing the car from the front, to the back in the center, under the windshield. The low pressure ac port and the high pressure ac port both have black dust caps. The low pressure ac port is the smaller of the two.

on Jun 14, 2015 | 2003 Peugeot 206

1 Answer

Where is the location of the low pressure port to recharge air conditioning system? There are two ports located on passenger side about 2 inches apart on chrome pipes.


There is two filling ports for A/C - high pressure is biggest diameter-low pressure smallest one.All of them must have black cups.Because I don.t know exactly the model of your VW I can.t dive you proper instruction.If any problem come back with full details for the vehicle.

Jun 13, 2011 | Volkswagen Jetta Cars & Trucks

2 Answers

Where is the low pressure side of the air conditioner on the engine compressor


The Low Pressure Side port for AC is near the Throttle Linkage Connector centered in front of the engine. It has a black cap and says LOW.
  Connect the refill hose to the connector on the Low Pressure Side of the air conditioning system. The Low Pressure Side connector will be smaller than the High Pressure Side connector so the refill hose will fit properly only on the Low Pressure Side.
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.


 

Aug 10, 2010 | 2007 Dodge Ram Truck

2 Answers

How to recharge recharge airconditioner


Hi, determine if your car uses R134 or R12 refrigerant. You will notice screw type connectors on the both the High Pressure Side and Low Pressure Side lines in models using R12 refrigerant. R134 compatible models have quick connect valves on both sides. Models made before 1995 may use the old R12 refrigerant. If this is the case, you must have your Chrysler's air conditioning system retrofitted to use R134 refrigerant. Mixing R12 and R134 refrigerants is dangerous and may cause damage to your vehicle. Check your air conditioning system pressure using an automotive air conditioning pressure gauge. Keep in mind that in order to get an accurate reading, the air conditioner has be turned on the coldest setting with maximum blowing power. Remove the Low Pressure Side port valve cap and set it aside. The location of the port varies, but it is usually in front of the engine block. Attach the refill hose to the port on the Low Pressure Side of the air conditioning system. The Low Pressure Side port is smaller the High Pressure Side port. Because the ports are different sizes, the refill kit hose should fit only on the Low Pressure Side port. Additionally, the High Pressure Side port will usually have a red cap or be marked with an H or the word High Allow the air conditioner to **** the refrigerant out of the can by slowly turning the valve on the refill kit hose. Pay attention to the way you hold the can. Most kits will have you hold the can upright when you recharge the air conditioning system. It may take as long as 10 minutes to empty a single can. Turn the valve to the off position and remove the refill hose from the port. Recap the port before closing the hood. Let the air conditioner stay on for at least 30 minutes. This allows the refrigerant to move throughout the entire system.
Take care

Aug 03, 2010 | 2006 Chrysler Town & Country

1 Answer

Air condition blows hot air but it has freon


You may have created an over charged condition and at this point the a/c compressor will cut off on high head pressures. This can be verified by installing gauges to the systems high and low side service taps and reading the pressures.An overcharged system will start the compressor briefly but soon cuts off once pressure goes to 350 - 400 lbs on the high side. Acceptable pressures for this system should be no greater than 250 high and low suction should drop to 40-50 psi.You might recover the charge and evacuate the system,then try bringing the charge back to proper level.A sight glass in the reciever drier really helps determining proper fill.Once all bubbles have dissipated from the sight glass during charging ,one should stop at that point to avoid overfilling.Too much freon is worse than a low charge especially in hot ambient conditions....

Aug 26, 2009 | 2003 Saturn ION

1 Answer

Where do you recharge the airconditioning unit on a 98 jeep grand cherokee 4x4 loredo? Need the location of the fill valve. I already have the recharging kit.


Jeep GrandCherokee SUVs manufactured in or before 1995 use R12 refrigerant. You must retrofit these SUVs to accept R134 refrigerant using a retrofit kit available at your local auto parts store before you can recharge the system. In some areas, a license is required to retrofit an air conditioning system. If this is the case in your area, take your Jeep to a professional to retrofit the system.

Instructions:
  1. Step 1 Take your SUV to a mechanic to recover the R12 refrigerant out of the air conditioning system. A license and special equipment are needed to do this. Because R12 refrigerant is expensive, many mechanics will do the job for free.
  2. Step 2 Locate the Low Pressure Side connector port. You will find it on the driver's side of the engine. Remove the blue or yellow cap marked L. You only need to retrofit the system if you see a screw-type connector valve. If you see a quick connect valve, the system already is R134 compatible. Wipe the connector valve off with a clean towel. This ensures that the retrofit connector properly adheres to the valve.
  3. Step 3 Place the long retrofit connector from the automotive retrofit kit onto the Low Pressure Side valve. The retrofit connector has a special adhesive on the threads that will help it adhere to the valve. Screw the connector onto the valve. Tighten the retrofit connector using an adjustable wrench. Place the cap provided in the retrofit kit onto the retrofit connector. This keeps dust out of the system.
  4. Step 4 Follow the air conditioning lines away from the compressor until you see the High Pressure Side port valve. This is located near the Low Pressure Side service port. Remove the red cap and wipe the port off with a towel.
  5. Step 5 Put the shorter adapter onto the port. Twist it using an adjustable wrench until it is securely fastened to the port. Place the red cap from the retrofit kit onto the adaptor.
  6. Step 6 Fill out the Retrofit Identification sticker provided in the retrofit kit using a permanent marker. Remove the protective backing and place it on the interior side of the hood. This lets future owners and service professionals know that the system has been retrofitted.
  7. Step 7 Recharge the air conditioning system. See the related eHow titled "How to Recharge Air Conditioning with Freon in a Jeep Grand Cherokee."
WARINING:
Never try to evacuate the system yourself. A license and special equipment is needed to evacuate the system. Attempting to do this yourself will release refrigerant into the air, which is a federal crime.

Good luck (rated this help).

Aug 10, 2009 | 1998 Jeep Grand Cherokee

2 Answers

Low-pressure port I need identification


Basic AC system consists of Compressor pump (on engine), Condenser (front grill with radiator) and Evaporator (Firewall). Pump has two ports output (high pressure) and return (low pressure). Follow lines from pump. High side is usually between pump and condenser. Follow lines and find second port this will be low side (refill) port. Paint or replace port caps (red high, blue low). Also, refrigerant in system determines port size (R12 or R34).

Jun 24, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...