Question about 1987 Ford Bronco II

1 Answer

Automatic trans. only revers no fowerd fluid leavel ok 87 ford bronco 2 shift linkage seems ok. 4wd.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 722 Answers

Drain the tranny

Pull the pan and look for metal shavings - you may have lost your planetary gears. If so, you need a new tranny or have this one rebuilt.

Let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Posted on Jun 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need detailed instructions on how to replace the clutch on a 1987 Ford Bronco II, 4wd, manual trans, 6 cyl. Can you tell me where I might find this information online?


It is a copyright infringement to give info copied from a book ,unless you pay for it...I can tell you the fnt end of truck needs to be jacked up so you have plenty of room for repair.also if fluids are drained from trans and transfer case they will be able to handle better...
remove fnt and rear drive shafts and trans shift linkage . also the transfer case linkage . the speedo cable and wirig to trans will need to come off....now support the trans with a floorjack and remove the crossmember support... let the jack down a little to acess to top trans to engine bolts. thenremove all bolt except 2 ...one on each side take the bolts out of clutch slave cylinder and move away from your work...reposition jack to the center of trns and remove trans carfully.one hand on trans tail shaft and one on the jack handle. lower trans assembly to the ground after you have cleared the clutch..now follow instructions in new clutch and reinstall ...

Feb 17, 2011 | Ford Bronco II Cars & Trucks

1 Answer

I have an 1988 ford bronco 2 automatic V6 i pulled


There are shift solenoids in the transmission and apparently there's a problem them. I would get it to a trany shop and have it checked right away. If you continue to drive it you will ruin the transmission. Are sure you put the right computer in the vehicle? If you put a computer from a Bronco II with a manual trans in a vehicle with an automatic trans, the trans won't work right.

Jan 22, 2010 | 1988 Ford Bronco

1 Answer

1993 Jeep Grand Cherokee - V6 engine with a Automatic 4-speed Transmission. Unit will not shift out of 1-2 speed into 3-4 gear. I have checked shift linkage - is OK & TV linkage OK. Is there a vacuum...


The only thing that you can do is check the trans fluid.Start car,run it through all gears and end in neutral.Handbrake on.Now check the trans fluid level.Make sure engine is warm.If needed add fluid.If this is not the problem,a tranny expert is the go.There is not a lot anyone can do with an auto trans at home.Hope this helps

Jan 13, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Bronco II: automatic Transmission slow to shift gears


replace the torque converter or try to get the transmission flushed first by a professional auto trans outfit

May 05, 2009 | 1989 Ford Bronco

1 Answer

Bronco tranny wont shift out of first


sounds like you burnt it up. how long did u drive it like that?

Nov 04, 2008 | 1989 Ford Bronco

1 Answer

Ford transmission 86 4wd will not shift to high gear


It is hard to say from your description what the problem is ... could be linkage issue ... could be trans is going as is with the other poster ...
Losing overdrive. Clutches (bands/clutches) have had it. Be careful driving without that top gear ... doing too high a speed without the appropriate gear causes extra stress on your engine that could accelerate further problems. Try to do only driving at a low enough speed that the top gear is not missed ... will help the vehical last as long as possible.

Oct 13, 2008 | 1986 Ford Bronco

1 Answer

'87 bronco II transmission and transfer case


what engine? auto-manual? t-case mercon automatic fluid same for manual trans

Sep 21, 2008 | 1987 Ford Bronco

1 Answer

Shifting


Check the vacuum line that attaches to the front of the intake manifold to the transmission,( no cracks, splits, deteriated ends) sounds like vacuum is low

Aug 08, 2008 | 1986 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...