Question about 2002 Hyundai Santa Fe

Open Question

Valet Switch Where is the valet switch located? I trying to program a new keyless entry

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 740 Answers

SOURCE: Need to turn the valet switch off On 1999 Nissan Maxima

Look for alarm Brain box and look for wires coming out black and red going to valet switch. to turn valet on turn ignition in ON position and press-switch or flip depending on the type of switch. If it a basic alarm just disconnect the main wiring harness to alarm box- unplug and the car should start. Good luck and thanks for using FIX YA

Posted on Jan 27, 2009

  • 373 Answers

SOURCE: keyless entry programming instructions

can you check with dealer

Posted on Feb 04, 2009

mechanicm639
  • 253 Answers

SOURCE: WHERE IS THE VALLET SWITCH LOCATED

If you have an aftermarket alarm the valet switch is a small push button, or toggle switch. They are usually located under the drivers side of the dash Good Luck

Posted on May 13, 2009

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry: 2003 Hyundai XG350

The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

Posted on May 27, 2009

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry 2003 Hyundai XG350

I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 dodge intrepid. The alarm never worked on it. We bought it used and all of a sudden when we go to unlock the door it turns on. Now the car won't start. I've looked online for answers and...


The 2000 Dodge Intrepid is equipped with an alarm system that is triggered when unauthorized entry is attempted. In some situations, such as having the Intrepid valet parked or when it is being serviced by a mechanic, the alarm system needs to be disarmed so it doesn't go off. Disarming the alarm will prevent it from being activated until it is armed again.
Difficulty: Moderate Instructions

  1. 1 Insert the key into the ignition.
  2. 2 Turn the ignition switch to "ON." Do not start the engine.
  3. 3 Press and hold the valet/override button within five seconds of turning the ignition on. The valet button is located beneath the steering column.
  4. 4 Release the valet/override button after the security indicator light turns off.
  5. 5 Turn the ignition switch off.


have to do it in this order

Dec 10, 2010 | 2000 Dodge Intrepid

1 Answer

Valet switch location


I own a 1998 dodge durango and Keyless entry does not work all the time and sets my alarm off. There is a valet switch which will perminately disarm the alarm, but I a unsure of it;s location under the dash. Can you help me with this.

Jul 02, 2010 | 2000 Dodge Durango

1 Answer

How do i set car alarm


turn key to on position, just before it turns over. Within 5 seconds press and hold in the valet/overide button found under the dash area
until the blinking light in your dash area goes off and the siren chirps twice. If you have the toggle type, do the same but toggle on after turning key, then turn key off. This should reset the alarm. Repeating these steps places the vehicle back in valet mode. If you don't have the valet switch, you don't have an alarm. I don't seem to remember the 99 explorer having an alarm, and it does not show up in my manuals, only keyless entry.

Mar 22, 2010 | 1999 Ford Explorer

1 Answer

Security system status indicator light is flashing two times. It will not go out.


the keyless entry is in valet mode,i believe you must hold the unlock button down with the drivers door open to switch between valet and regular operation,this info is also in the owners manual good luck!

Jul 09, 2009 | 2000 Subaru Outback

1 Answer

Valet Switch/Button


Contact a dealer for the location of switch

May 02, 2017 | 2002 Mitsubishi Galant

1 Answer

Reset keyless entry on 1998 honda civic


Okay, here goes-

1. Turn Key to on position.
2. Push and hold **valet button on the stock radio.
**Valet button is skinny bar located between am/fm & cd/tape buttons on stock radio.
Door locks will cycle one time.

3. Press any button on remote one time within 20 seconds. Door locks will cycle again.
4. To program up to 4 additional remotes repeat step 3 for each additonal remote.
5. Turn key off programming is complete.

Thanks for using Fixya, please rate if this helps :)

Mar 16, 2009 | 1998 Honda Civic

2 Answers

How do i disable alarm for my 1996 thunderbird lx 4.6


Ok, try this.
Put the key in the ignition, and turn forward
all the way just before cranking. Then within
5 seconds, press and hold in the valet/overide
button, found under the dash area in most cases,
until the installed LED (the blinking light)
in your dash area comes on solid.
(Your valet switch might be the toggle (on/off) type.
in this case, key on, flip switch in oposite direction,
key off.)

This should be valet. This overides
the starter kill relay in the alarm harness,
and returns the car back to disarmed mode.

The only thing that will work now on your system,
is the keyless entry if installed.

Just Repeat these steps to rearm your system.

Feb 18, 2009 | 1996 Ford Thunderbird LX

1 Answer

I want to turn off factory installed alarm in 1999 Ford Taurus SHO but where is the switch located?


Hi there. As far as the valet/overide button, it's a hidden
device-switch, a little spring loaded micro button,
red or black possibly and is probably down under
the dash area, near your knee/leg. In some
remote start/alarm combos, the antenna on the window
glass will also have an override/valet button.
Older sytems will have a flip type toggle switch.

When you locate the button or switch,
turn on the ignition key, press and hold
in the button until the alarm chirps 1 time
(for toggle types, key on, flip switch in the
opposite direction, then key off). This should over ride the system. You would get a single chirp to confirm from the siren.
The LED (light emiting diode) light in the dash
should also go on solid. This is valet/overide/reset.
This should correct any issues like starter disable,
or anti-hijack. Your keyless entry, if installed,
will still be operable. The have it inspected for the
falsing issues you are experience at a local shop.
You would repeat the same steps to toggle back into user mode.

Sep 01, 2008 | Ford Taurus Cars & Trucks

1 Answer

Keyless entry


You Need Vas5051 Or Vag-com Equipment To Programe It

Jul 19, 2008 | 2004 Audi A4

1 Answer

Wont go into program mode


yes there is actually if you have a valet switch there is a code you set in that gives you control over setting the keyless remote code i dont have the specs and you would probably have to take to dealership so they could show you how to set up valet switch for keyless entry since i do not have a book for that spec also theres this link that they can help set up over the keyless entry remote by there techs call the number give them alarm model and info on truck
http://www.remotesunlimited.com/?OVRAW=car%20alarm%20remote&OVKEY=car%20alarm%20remote&OVMTC=standard&OVADID=2211521522&OVKWID=21052597022
heres the link call the tech they sale to all dealers and have techs on hand during service hours to help

May 22, 2008 | 2003 Ford F150 Regular Cab

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...