Question about 1999 Dodge Intrepid

1 Answer

Taking off thermostat - 1999 Dodge Intrepid

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

You remove the rad hose on top of the engine and pull the thermostat out and replace it and reconnect the rad hose

Posted on Jun 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you change the thermostat on thencar


The thermostat is under where the top radiator hose joins the block.
Just unbolt the housing and take it out. Make sure that you put the new one in the same way as the one you take out. Fit a new gasket and be sure that the housing it seated correctly and do all the bolts up gently and evenly before the final tightening.

Jul 05, 2011 | 2001 Toyota Camry

1 Answer

I need to change the thermostat in my Taurus. Where is it located? Is it a difficult change?


if you find top hose follow it to engine -thermostat housing have to bolts most times /1)drain coolant 2)take about bolts pull up housing take out thermostat 3)put thermostat in (note;how thermostat is turned put new one same way) clean housing good 4)put gasket on with little bit of sealant tigthen bolts 5)put hose back on 6)fill up radiator with coolant &let run till warm up [check for leaks while warming up }top radiator off ;;;;;done

Nov 05, 2010 | 1998 Ford Taurus

1 Answer

How do you replace the thermostat on a 2002 chevey malibu


Where the top radiator hose clamps to the engine is the thermostat housing. Take hose off. Take two bolts off. See how old thermostat comes out so you can put new one in the same. Use blade or scraper to clean both surfaces well. Put gasket and new thermostat in and bolt it down. Re clamp hose and refill coolant. Check for leaks

Oct 02, 2010 | 2002 Chevrolet Malibu

2 Answers

Can i take my thermostat out without harming the engine


yes, as long as the car is not running, it will be fine to take the thermostat out. just remember which way the thermostat came out so you will put the new one in properly, otherwise it can make your engine overheat.

Aug 08, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Finding thermostat housing for 2002 cavalier


for the 2.2L engine follow the lower radiator hose it will take you to the thermostat housing. the 2.3L 2.4L follow the coolant inlet pipe it will take you to thermostat hosing.you have to remove exhaust manifold heat shield to remove thermostat housing.

Dec 14, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

How do i take thermostat out?


1. Thermostat on this particularcar is on the right-side of the inlet manifold.
2. Allow the engine to cool down for about 3-hours before this removal is attempted.
3. Place a conatiner under the radiator.
4.Drain the coolant into the container by opening the radiator drain valve( which is under the radiator).
5.Disconnect the radiator hose clamp.
6.Pull the upper radiator hose off the thermostat housing cover.
7 Remove the thermostat bolts.
8. Carefully note the position of the old thermostat in its seating place. (arrow is marked on its seating place)
9.Take out the old thermostat.
10.Break off the old gasket seal using a knife or similar object.
11. Reverse this procedure for installation .(rememeber to put in new gasket on the thermostat seating place).

Dec 09, 2009 | 1992 Subaru Legacy

2 Answers

How does a thermostat housing in a 99 cougar look like and should i empty my coolant before i change my thermostat


you need to change the coolant every 2 years because it will start to break down and then will do damage to the radiator and the heater core. You don't have to empty if the coolant is good, The top radiator hose will hook to the radiator and to the thermostat housing. You need to take the housing off to get to the thermostat.

Dec 03, 2009 | 1999 Mercury Cougar

1 Answer

Need to replace thermostat but not sure where it is located in a 1995 Lexus Es300


Follow the lower hose up to the water pump where there is a housing for the thermostat. To remove this you will first, want to take the front right tire off then the dust guard for it; the thermostat housing should now be viseable. Then you will want to take the plastic windshield washer, and engine coolant reserviors off to make the job easier. Next take the bottom rad. hose off the water pump(where it goes to, from the radiator). then struggle for awhile with taking the three nuts that hold the thermostat housing together (a wobbler bit on a socket wrench can make this job easier). Once these are off you can unplug electric plug on top of the housing, pull that part of the housing off and there the thermostat sits in all of its evasive gloriousness waitng for you .

Nov 16, 2009 | 1995 Lexus ES 300

2 Answers

How do i replace the thermostat in a 2001 pontiac montana?


  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
  7. Remove the thermostat.
  8. Install the thermostat.
  9. Install the thermostat housing bolts and tighten them to 18 ft. lbs. (25 Nm).
  10. Install the radiator hose to the thermostat housing.
  11. Install the crossover exhaust pipe.
  12. Install the air cleaner and duct assembly.
  13. Good luck...
  14. Fill the cooling system.
  15. Install the thermostat housing and gasket.
  16. Clean the mating surfaces.

Jan 15, 2009 | 2001 Pontiac Montana

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...