Question about 2003 Pontiac Montana

1 Answer

My van pontiac montana 2003, and I took it to a shop, and said that It needs the all-motor mounts replaced. my question is: How do you replace the motor mounts specially the one on the transmission?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello there I have a 2003 montana since it hit 200,000 k's its making this weird sound from the front end, like a humming when you speed up , or driving normal not sure what is going on , can you help me out ...

Posted on Mar 03, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 159 Answers

SOURCE: How do I install a rear wiper motor on 2003 Pontiac Montana?

Here's a great video that will show you how to install the rear wiper motor on a 97-05 Montana or Venture">

Posted on Mar 02, 2011

  • 1 Answer

SOURCE: transmission problem 2004 pontiac montana van

my 2000 montana just started to do this mine is the TCC (torque converter control) switch inside the tranny dealer said around $2000 to put it in and the part only cost $52 and lucky me im outta warranty isnt that funny how that works i think im just gonna sell it HOPE THIS HELPS YOU GUYS

Posted on Apr 10, 2009

  • 55 Answers

SOURCE: replace thermostat 2003 pontiac montana

yes but with the right shaped wrenches and tiny hands it can be done without removing the exhaust crossover pipe

Posted on Oct 16, 2008

  • 1050 Answers

SOURCE: 2003 Pontiac Montana Front Wheel Bearings

Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Posted on Apr 08, 2009

  • 15 Answers

SOURCE: 2003 pontiac montana leaks condensate water in the drivers floor

Bet the drain is clogged with leaves. Look under the blower motor under the hood. Can almost be that the cowling has been filled with leaves at one time or another. Got to clean that stuff out every now and then.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replacing Motor Mounts

Best left to a repair shop
They have the lift,tools & equip, as well as
experience to replace mounts
Do them all,motor & transaxle

Jun 24, 2013 | 2002 Pontiac Montana

1 Answer

I need to jump start our second vehicle using the Montana van. I can't find the negative battery terminal to connect to.

Typically next to the battery, there will be a terminal looking plug on the shock mount. That is where you will attach the negative for jump starting the vehicle. Basically, you just need to ground out the wire somewhere, so when they built the van, they included a perfect ground.

Oct 14, 2011 | 2003 Pontiac Montana

1 Answer

The 2001 Montana van with a V-6 uses a lot of coolant and there is the smell of burning anti-freeze. It runs very well as of now.

my 2000 pontiac has code 420 when on idle is ok on drive or park I step on the gas it drives like motor mounts are broken I let the gas go and it rolls good I change coils wires plugs crank shaft speed sensor I even took of converter thinking it was plug it,on stray pipe replace EGR and still have the same problem, please help lucky fly 119@ thanks

Sep 16, 2010 | 2001 Pontiac Montana

1 Answer

My air conditioning does not blow cold air, just warm air? What part needs to be replaced? i have a 2003 pontiac montana van

You may just have to have the system recharged with coolant. When was the last time it was checked?

Jun 23, 2010 | 2003 Pontiac Montana

1 Answer

Where is the horn located on a 2003 pontiac montana van? mine needs to be replaced.

It looks like this van gas 2 horns, on each side of the vehicle behind the bumper. Easiest way to get to these would probably be to remove the inner wheel well covers. Try just crawling underneath first to see if you can see them though.

Mar 30, 2010 | 2003 Pontiac Montana

1 Answer

Where is the computor placed in my van pontiac montana 2003

Hello Burger.

The engine control module is mounted on the left front under the hood to the left of the air filter.
It is under a plastic cover.
Hope your repair goes well for you.


Mar 02, 2010 | 2003 Pontiac Montana

1 Answer

Replace seats in 2003 Montana with seats from 2000 Montana

I would disconnect the battery minus - cable first, ensure the airbag connectors are the same ! otherwise I do not think you have a problem !!

Aug 11, 2009 | 2003 Pontiac Montana

1 Answer

Pontiac Montana

You'll have to replace the entire assembly if you're missing the mounting piece that the mirrors sit on inside the housing... You'll need to remove the door panel in order to remove the panel that's right beside the mirror on the inside of the door and remove the 3 bolts holding the mirror down assembly down....

Aug 11, 2009 | 2003 Pontiac Montana

Not finding what you are looking for?
2003 Pontiac Montana Logo

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides