Question about 2000 Mitsubishi Galant

2 Answers

Only the radio and windshield wipers will work with ignition in Acc position. Everything works in On position. Every time I turn the car off and back on I have to reset the radio (CODE). Battery checked out OK. Started this morning. Now cars dies within one minute after starting. Starts fine. Misses some during idle.

Posted by on

  • pta4uk Jun 02, 2010

    Only the radio and windshield wipers will work with ignition in Acc position. Everything works in On position. Every time I turn the car off and back on I have to reset the radio (CODE). Battery checked out OK. Started this morning. Now cars dies within one minute after starting. Starts fine. Misses some during idle.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 75,817 Answers

I would suspect the ignition switch may be defective, this switch is the actual electrical switch that turns the power on in the car, not the ignition lock cylinder. the switch is at the end of the ignition lock cylinder, to access the switch u must remove the plastic covers on the steering column, there are four screws i think recessed into wells in the lower cover, here is the part number and a picture of this switch. also before u start with the switch make sure all the fuses are good in the fuse box.

STANDARD MOTOR PRODUCTS Part # US320
$30.00


Only the radio and windshield wipers will work - 6e57f02.jpg

Posted on Jun 02, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 17,970 Answers

We will can assuming that you have any problem with the ignition switch, because this action is cancel all electrical connections (battery), so you need re-enter the radio code or armed the theft car system (died after run few secodns).

Tell us news.

Posted on Jun 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

I have 2006 infiniti g35 coupe that the wipers start working when i turn the key to acc position and the wipers swicht off


wipers should normally work in the run position of the ignition switch. Accessories position is for radios , cig lighter and other items that you need when stationary with the engine off.

Jan 15, 2014 | 2004 Infiniti G35 Sport Coupe

1 Answer

Wiper wiring diagram


Those are accessory functions working off the ignition switch when in accessory position or run position of the key. Were you to check if the wiper and radio fuse had power to them in the run or accessory position as they should, likely they would not. Power from the switch goes to the fuse panel, powering the fuses and circuits that only work with key in on or acc., either a direct wire to the fuse panel or sometimes, fuses get power from an accessory relay that sends power to fuses, but relay has to get a signal from a good working switch before it powers the fuses.
What I'm trying to say, is the bad switch is probably the reason you have no wipers, radio, or mirrors.

Aug 31, 2013 | Cars & Trucks

1 Answer

When I start my 96 ford Taurus I have no radio or windshield wipers or speedometer. But when turn key backwards radio and wipers work


I am betting it is your ignition switch- it is just like any other type of switch, in that it has contacts that eventually wear out. Once you turn the key to start the car, it returns to a position that maintains the contacts to power your accessories, and it sounds like those contacts inside the ignition switch are worn or broken. The "acc" contacts when you turn the key backward are rarely used so they are still in good shape, unlike the "run" contacts which get hit every time you start the car.

Jan 17, 2012 | 1996 Ford Taurus

1 Answer

I have a 1999 Mercury Sable with a 3.0 24V DOHC. I got into it this morning and noticed the radio,clock, heater, (whole panel is out) and windshield wipers, speedometer and tack are all not working. But...


It might be worth your time to replace the ignition switch. The power through the switch is working off the Acc lead for most of the things that work while the car is not running, so the wires are still connected.

Apr 06, 2010 | Mercury Sable Cars & Trucks

1 Answer

I changed the relay fuse to my windshield wipers and the knob and my wipers still wont work on my 98 plymoth grand voyager what should i check


Turn wipers on (veh in "on" or "acc" position)
Disconnect the electrical connection at the windshield wiper motor (located in the engine compartment on the fire wall) and check for voltage. If you have voltage, there is a good possibility your windshield wiper motor is bad.
You may also: Disconnect the electrical connection at the windshield motor and run a heavy gauge wire directly from the positive side of the battery to the motor. If you get the windshield motor to come on. There may be only a wiring (short) problem between the relay and the motor.
Let me

Jan 21, 2010 | 1989 Plymouth Reliant

1 Answer

How do I remove the windshield wiper motor from a Ford F-250?


2002 Ford F-250 Windshield Wiper Motor Removal & Installation 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFF position to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

Nov 09, 2009 | 2002 Ford E250

Not finding what you are looking for?
2000 Mitsubishi Galant Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...