Question about 1995 BMW 5 Series

1 Answer

I have replaced theromstat,water pump and waterpump pulley and car gagr goes into the red in about 10 mins. i did find the radiator fan switch line broken wire broken, Help

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 437 Answers

Fan clutch isn't spinning the fan to pull air to cool car. replace fan clutch assembly. that fan alone should keep the car in the mid zone. electric auxillary is for A/C and overheating only.

Posted on Jun 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can i replace the water pump in a 1997 Nissan pickup without messing with (replacing) the timing chain?


D21 Pick up? The water pump is not timing belt driven. It is drive belt drive with a pulley held on with 4 bolts.

So, yes, the water pump can be replaced without touching the timing components. :-)

Nov 22, 2011 | 1997 Nissan Pickup

1 Answer

95' ford econline 350 van replacing waterpump and clutch fan how to replace.


TO REPLACE WATER PUMP.REMOVE THE RADIATOR SHROUD HALVES.REMOVE FAN CLUTCH AND FAN.YOU NEED FAN CLUTCH WRENCH AND A FAN CLUTCH PULLEY HOLDER.YOU CAN RENT TOOLS AT AUTO ZONE OR BUY THEM AT A AUTO PARTS STORE.THE FAN CLUTCH BOLTS ARE LEFT HAND THREAD. REMOVE THEM BY TURNING CLOCKWISE.BEFORE INSTALLING NEW WATER PUMP COAT BOTH SIDES OF WATER PUMP GASKET WITH GASKET SEALER.TORQUE WATER PUMP BOLTS 18 FT LBS.

Mar 15, 2011 | 1995 Ford Econoline

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

2 Answers

How to locate and replace water pump on 2006 chevy trailblazer


The water pump is usually mounted center, Front of the engine and is run by a belt. Look for the location the water lines connect to that has a pulley attached.

Jul 11, 2010 | 2006 Chevrolet Trailblazer Ext

2 Answers

How do I change the water pump on a 2004 chevy trailblazer 4.2L?


dont change a water pump unless it is leaking from the pump itself. if your vehicle is overheating check the simple items first. a water pump very rarely goes bad.

Apr 12, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

I believe the bearing on my waterpump is bad. while driving the fan began rubbing the shroud and eventually wedged against the waterpump pulley. before removing the radiator,shroud and hoses i checked...


You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off.

Feb 22, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

2 Answers

Heating problem


Check theromstat, also test coolant probe be sure it is sending good signal. Also you may need to oversize the waterpump pulley. Be sure the pump is moving the coolant .

May 23, 2009 | 1996 Nissan Sentra

1 Answer

Water leak/waterpump problem


The water pump is where the alternator pulley and radiator fan is connected. It has a hole on its body called "weep hole". If the seal and bearings are already worn out, coolant can be seen leaking at this hole. To replace it, you will have to remove the upper radiator hose, the fan blades, and the alternator pulley. Just unbolt the old one, clean the mating surfaces, install a new gasket, then install the new pump.

May 01, 2009 | 1999 Suzuki Vitara

2 Answers

Chev Montecarlo 3.4 waterpump replacement


Not difficult at all. Drain radiator. Use 10 millimeter wrench and loosen water pump pulley bolts. The easy way to prevent pulley from turning is place a 3/8 inch drive ratchet in the belt tensioner and increase belt pressure to hold pulley. After bolts are loose, relieve tension on belt to remove it. Then remove bolts from pulley followed by pulley itself. There are 5 8 millimeter headed bolts holding pump on housing. Remove all five, clean housing surface, install new pump and gasket. Although there are five holes it will only line up one way. Pay attention to the removal of the original pump to line up new one. Reverse removal proceedure. Open bleeder screw(s) when refilling radiator. One will be one the metal tube above the water pump housing. The other will be at the opposite end of the engine where the radiator hose meets a metal outlet. This one will need to be opened a few times to bleed air as the thermostat opens after engine is cranked. Hope this helps.

Apr 07, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
1995 BMW 5 Series Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...