Question about 2006 Ford Focus
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
it resets itself.
Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The PATS will be activated and will disable the vehicle from starting if there is a:
Posted on Feb 22, 2009
its quite quite simple;take your pipes of and block them off reconnect them to new pump and replace pump to in line belts.adrian;;;
Posted on Nov 14, 2009
If you lay down under your vehicule, once you're under the oil pan (when your head is toward the back) check the bottom of the engine block to your right. It should have the size of a can soup and should be fixed there.
Hope it will help
Posted on Dec 31, 2009
the only way is to connect with a ecu analyzer-programmer to a authorized or specialized service garage to find the cause and reset the ecu.
Posted on May 28, 2010
SOURCE: 2006 ford focus rear brakes
If the piston is stuck out this is due to a seized calliper however a temp Fix is to turn the piston clockwise to force it back in as rear callipers are self releasing so they need to be turned clockwise they will not go stright back without turning. This is due by broken calliper seals although you will temp fix it, It's best to either replace calliper or buy a calliper fixing kit which includes all the seals that need replacing.
Also You will need to Empty the brake fluid out to make it easier to push the piston in it, Then you will need to bleed the whole brake system once fitted back.
Posted on Jul 21, 2010
Tips for a great answer:
Dec 04, 2016 | Ford Focus Cars & Trucks
Nov 23, 2016 | Ford Cars & Trucks
Jul 16, 2016 | Ford Cars & Trucks
Jan 14, 2016 | Ford Cars & Trucks
Oct 30, 2015 | Ford Cars & Trucks
Aug 23, 2015 | Ford Cars & Trucks
Jul 25, 2014 | 2006 Ford Focus
Apr 03, 2013 | 2003 Ford Focus
Jan 14, 2010 | 2000 Ford Focus
1,087 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: