Question about 2002 Dodge Intrepid

3 Answers

Where is the thermostat located on a 2003 dodge intrepid

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

ITS NOT THE TOP HOSE THE TOP HOSE GOES TO A HOUSING BUT THERES NO THERMOSTAT THERE I JUST DID ALL THAT WORK TODAY TO TURN UP WRONG

Posted on Jul 01, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Follow the bottom hose to the thermo housing and there will be a plastic housing and the housing will need to be replaced as well as the thermostat. best advice is when its fixed [sell it]

Posted on Aug 22, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 333 Answers

Follow the top radiator hose back to the motor.Should be right there.Remove two bolts and inside should be the thermostat

Posted on Jun 02, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 55 Answers

SOURCE: THERMOSTAT PICTUREDIAGRAM OF 1999 DODGE INTREPID, 2.7 ENGINE SIZE

It is located on the left side of the engine down where the lower rad hose meets the engine block. It is fairly difficult to change.

Posted on Oct 18, 2008

Mr BrokRench
  • 1623 Answers

SOURCE: what is the quickest way to change a thermostat on

Hello Kalel6877...the "quickest" way is let a shop put it on a hoist and do it...but if you want to tackle this one i'll walk you through it.
Raise your Dodge Intrepid with a jack and lower onto jack stands, or use wheel ramps. Set parking brake and/or chock wheels
Disconnect the negative cable from the battery. Open the drain plug at the bottom of the radiator and drain the coolant into a suitable container.
On Intrepids with 2.7L engines, follow the lower radiator hose to the thermostat housing. Loosen the hose clamp at the end of the radiator hose with a screwdriver and pull the hose off the thermostat housing.
Unbolt the two bolts holding the thermostat housing cover on and pull off the cover. On 2.7L Intrepid engines, it is easier to gain access to the thermostat housing behind the alrernator by working from beneath the engine.
Note the position of the old thermostat and remove. Install the new thermostat with the spring-side facing into the engine. Clean any old gasket residue from inside the thermostat housing cover. Install the new thermostat gasket.
Reinstall the thermostat housing cover and tighten bolts to 105 inch/pounds. Reattach the radiator hose and tighten the hose clamp. Refill the radiator with reserve or new coolant. Reattach the negative battery cable.
Start your Dodge Intrepid and allow it to run with the heater on high until it reaches normal operating temperature. Check radiator hose for leaks and tighten the hose clamp to stop any leaks, if necessary.
Thats about it...jack her down and pat yourself on the back.
Good luck..i hope this helps...please take time to rate me a fixya.

Posted on Jul 18, 2009

  • 312 Answers

SOURCE: Chrysler intrepid 2003 obd 2 code P0441

Most common problem causing this code is the purge solenoid. A quick smoke test will show if you have any leaks in the system. If no leaks and the fuel cap is installed properly it's the purge solenoid.

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace thermostat on 2003 intrepid 2.7 liter


Find the top radiator hose. Move away from the radiator to the engine block. Where the hose connects to the engine block that is where the thermostat is.

Aug 27, 2014 | 2003 Dodge Intrepid

2 Answers

How to replace thermostat on 2003 intrepid 2.7 liter


Why do you need to replace thermostat.? Is it not getting hot enough via the heater,or is the engine water boiling? Its usually at the end of the bottom hose nowadays,youll see a round housing,two or three bolts.Drain the water first,or undo the bolts,engine cold,and catch the water.Replace with an original thermostat,and double check the sealing ring is in place on the new one.Refill radiator.Run engine,check water level later,with heater on hot

Aug 27, 2014 | 2003 Dodge Intrepid

1 Answer

Water leaking from thermostat area (not weep hole) on a 2003 intrepid 2.7


Pull the thermostat off there is a sealant that goes down before you put the gasket on use this on both sides of the gasket then place your thermostat back on

Sep 12, 2012 | 2003 Dodge Intrepid

2 Answers

Looking for a picture of the diagram of where the thermostat is located on my 1998 2.7 liter dodge intrepid PLEASE!!!!!


Hi, I don't have a picture, but trace the big hose from the bottom of the radiator to the engine, and it will be under the housing where the hose connects.


2.7L Engine

  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Remove radiator lower hose from thermostat housing.
  4. Remove nuts from heater tube flange studs.
  5. Loosen starter bolt at heater tube bracket.
  6. Pull heater tube out of thermostat housing and position out of the way.
  7. Remove bolt and two studs.
  8. Remove thermostat housing, O-ring and thermostat.
  9. Remove thermostat housing bolts.

To install:
  1. Clean gasket sealing surfaces.
    NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  2. Install thermostat and seal into thermostat housing .
  3. If removed, install two studs.
  4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  5. Lubricate new heater return tube O-ring with coolant.
  6. Position heater return tube flange over two studs. Install nuts.
  7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  10. Refill cooling system.
  11. Inspect for leaks.
  12. Connect negative cable.

Mar 26, 2011 | 1999 Dodge Intrepid

1 Answer

Location of thermostat on 2003 dodge intrepid


follow upper rad hose towads block. it'll be on that hose

Jan 02, 2011 | 2003 Dodge Intrepid

1 Answer

Where is the thermostat located on a 2001 Dodge Intrepid


Hi:
Your thermostat is located under the housing where the upper radiator hose connects to the engine. The housing is held to the engine with bolts,and has a gasket that must be replaced when you replace the thermostat. Make sure all surfaces are cleaned before reassembly.

Dec 10, 2009 | 1999 Dodge Intrepid

1 Answer

Whwere is the thermostat located on a 2004 dodge intrepid?


The thermostat on the 2.7 L and 3.5 L engines are located on the lower left side of engine, near the front.522ad18.gif904400a.gif

Oct 03, 2009 | 2004 Dodge Intrepid

1 Answer

What is the quickest way to change a thermostat on a 2003 dodge intrepid


Hello Kalel6877...the "quickest" way is let a shop put it on a hoist and do it...but if you want to tackle this one i'll walk you through it.
Raise your Dodge Intrepid with a jack and lower onto jack stands, or use wheel ramps. Set parking brake and/or chock wheels
Disconnect the negative cable from the battery. Open the drain plug at the bottom of the radiator and drain the coolant into a suitable container.
On Intrepids with 2.7L engines, follow the lower radiator hose to the thermostat housing. Loosen the hose clamp at the end of the radiator hose with a screwdriver and pull the hose off the thermostat housing.
Unbolt the two bolts holding the thermostat housing cover on and pull off the cover. On 2.7L Intrepid engines, it is easier to gain access to the thermostat housing behind the alrernator by working from beneath the engine.
Note the position of the old thermostat and remove. Install the new thermostat with the spring-side facing into the engine. Clean any old gasket residue from inside the thermostat housing cover. Install the new thermostat gasket.
Reinstall the thermostat housing cover and tighten bolts to 105 inch/pounds. Reattach the radiator hose and tighten the hose clamp. Refill the radiator with reserve or new coolant. Reattach the negative battery cable.
Start your Dodge Intrepid and allow it to run with the heater on high until it reaches normal operating temperature. Check radiator hose for leaks and tighten the hose clamp to stop any leaks, if necessary.
Thats about it...jack her down and pat yourself on the back.
Good luck..i hope this helps...please take time to rate me a fixya.

Jul 18, 2009 | 2003 Dodge Intrepid

2 Answers

How do you replace a water pump on a dodge intrepid 2003


The intake where the thermostat goes is in the driver side of the motor behind the altenator. I had to remove the front clip of the car and the altenator to get to it. It is quite a job.

Jul 20, 2008 | 2002 Dodge Intrepid

Not finding what you are looking for?
2002 Dodge Intrepid Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...