Question about 2004 Jeep Wrangler

1 Answer

I have a 2004 jeep wrangler with a manual trans rattle in nutral

I have a 2004 jeep wrangler x with a manual transmission and when in nutral and the clutch out it rattles. Is this normal? Or does it need fixing? Other than the rattle in nutral, it shifts and runs fine.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

It's not normal, it sounds like the throwout bearing may be making the noise. It's hard to say how long it will hold up. I've seen them make noise for a while. I would check the fluid level in the clutch master cylinder.

Posted on Jun 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not stay in 4wd


either solenoid is not holding or transfer case is not engaging completely..also check transmission fluid level.. if low..fill to full..

Dec 15, 2013 | Jeep Wrangler Cars & Trucks

1 Answer

I have a 04 jeep wrangler with the code po733


po733- gear 3 ratio incorrect
this is how to fix. You can try replacing the shift solenoids inside the transmission as long as the trans fluid is nice and clean looking it will be nice red color . If the trans fluid is dark or burnt looking , it maybe time for a new ******

Aug 07, 2011 | 2004 Jeep Wrangler

1 Answer

I have a 1989 jeep Wrangler 4cyl.2.5l manual transmission . It does turn on good and it does shift into gear but it wont move at all ????


is the transfercase in nuetral ? check that as that is the only thing that could stop a manual trans from moving trk unless the output shaft in trans broke but that only you will know.

Apr 03, 2011 | 1989 Jeep Wrangler

1 Answer

I have a 97 jeep wrangler with I-4 manual trans. Rattle in trans at a stop with clutch in and out. at one time there was a whine also but now that is gone. I dont drive this much. only 52,000 miles on her....


Rember when you press the clutch in, the pressure plate releices the clutch disc and input shaft in the transmission. If you still have noise, It can only be either a broken spring on the pressure plate or the throw out berring. Neither can be serviced. There is a fill plug on the side, It takes ATF

Jun 18, 2010 | 2004 Jeep Wrangler

1 Answer

Have a 2004 jeep wrangler x with a manual transmission and when it is in nutral and the clutch out it rattles. Is this normal? i still have the factory warranty and went to a chrysler dealer and they tried...


A rattling noise from the transmission is never a normal condition no matter what anyone says, and the first thing to do is to check the transmission fluid level, but it sounds to me like the throw-out/release bearing is riding the clutch pressure plate, and when the clutch pedal is in the up position the throw-out/release bearing and the clutch pressure plate should not be touching each other, and the only time that they should make contact is to release the clutch disk in order to shift the transmission into gear. There should be about 1 to 2 inches of free play in the clutch pedal, and the clutch should start to grab within 1 to 2 inches of letting the clutch pedal up off of the floor, and if this is not the case you might need to have the clutch properly adjusted especially if the clutch does not start to grab until the clutch pedal is half way up from the floor. Also, the main bearing in the transmission could be going out due to low fluid, or a damaged pilot bearing that is allowing the transmission input shaft to wobble just enough to cause a rattle from the main bearing or even a vibration in the transmission.

Jun 02, 2010 | 2004 Jeep Wrangler

1 Answer

Jeep 1997 Wrangler. Gear shifting very hard


synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Aug 19, 2009 | 1997 Jeep Wrangler

1 Answer

Jeep auto trans skips second gear


That transmission drum is gone, no other alternative to dismantle and repair.

Jul 16, 2009 | 1993 Jeep Wrangler

1 Answer

2000 jeep wrangler are sythetic lubes used in axils and trans


Hello grega1967, your Jeep Wrangler came from the factory with gear oil in the axles and manual transmission, but the transfer case uses transmission fluid. It is a NP231 and your axles are Dana 30 in the front and Dana 35 in the rear. They should have a 4.10 gear ratio due to you having a 2.5 liter 4 cylinder.

I hope this helps,

map6260

Mar 12, 2009 | 2000 Jeep Wrangler

Not finding what you are looking for?
2004 Jeep Wrangler Logo

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...