Question about 1990 Ford F150

1 Answer

Where can i locate the ignition control module on a 1990 f150

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 88 Answers

Here is where can i locate the ignition control module on - c29a0ee.gif

Posted on Jun 02, 2010

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

frankzen
  • 19 Answers

SOURCE: Where is the Ignition Control module located on a 1990 Ford f150

The ignition module is held on to the distributor by two 5.5mm bolts, but there is a tool for getting those bolts out. And you're right they are prone to failure.

Posted on Apr 04, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

techbuster
  • 5081 Answers

SOURCE: Where is the ignition control module located on a

Center of firewall. It is a black plastic box with 2 screws or e the ignition module could be mounted below the steering column.

Posted on Jul 04, 2009

emissionwiz
  • 75822 Answers

SOURCE: Location of ignition control module on 85 Chrysler Fifth Ave.

it is on the firewall in most models, here is picture

d93987c.jpg

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 FORD F150; 351 WINDSOR 5.8 V8 ENGINE; HAS NEW DISTRIBUTOR COIL AND IGNITION CONTROL MODULE STILL WONT START


crankshaft position sensor is bad. it uses this sensor to tell the computer when to make each plug fire. no signal no fire.

Nov 21, 2013 | 1990 Ford F150

1 Answer

Ignition control module location on a 1992 Ford Truck F150 1/2 ton P/U 2WD 4.9L FI 6cyl


I believe it is mounted on the distributor.. It is bolted onto the distributor with two small screws. It is called a TFI Module (Thick Film Integrated) module. It is gray in color and about 1 inch wide maybe 3 inches long with a connector on one end.

Jan 30, 2013 | Ford F-150 Cars & Trucks

2 Answers

Where is the ignition control module located on a 1990 buick lesabre


For 1990 Buick Lesabre 3.8L FI OHV 6cyl the Control Module-Ignition is located: Under hood, passenger side, front engine area, mounted on upper passenger side of cylinder head under ignition coil.

Hope helps (remember to rate this answer).

Apr 11, 2011 | 1990 Buick LeSabre

1 Answer

Locate ignition module 1990 BMW 316i E


The ignition is controlled by the motronic control unit its mounted on the passenger side of the dash above the glove compartment.

Jan 30, 2010 | 1990 BMW 3 Series

1 Answer

Where do the ignition control module located in a honda accord 1990 ex


The ignition control module (igniter) is inside the distributor, as is the coil on your Accord (1990).
Hope this helps you find it (it looks vaguely like a circuit board with tabs on it).

Nov 16, 2009 | 1990 Honda Accord

2 Answers

1990 ford f150 will run with fuel sprayed in intake new fuel pump and relays what else can it be


the only thing else to make it run is the ignition probably the ignition module

Nov 06, 2009 | 1990 Ford F150

1 Answer

1990 ford f150 5.8 no fire


Remove the ignition module and take to your local parts store for testing. It should be located on the side of your distributor were the wire harness plugs in. This will fix it 90% of the time.

Sep 07, 2009 | 1990 Ford F150

2 Answers

Wont start or has problems starting


Chek fuel filter first, and replace if it hasn't been changed in a while. Then if it still has problems starting, check ignition module. Make sure all grounds are tight and making good contact as well.

Aug 19, 2009 | 1990 Ford F150

3 Answers

Where is the Ignition Control module located on a 1990 Ford f150


The ignition module is held on to the distributor by two 5.5mm bolts, but there is a tool for getting those bolts out. And you're right they are prone to failure.

Apr 04, 2009 | 1990 Ford F150

1 Answer

1990 f150 transmission up shift to early


your modulator valve is unhooked, or bad. The modulator valve is what tells the transmission when to shift and what gear to shift to. It is located on either side of the transmission depending on the model, Im not sure which side your perticular model be on but it looks like a spark advance. I hope that helps you out.

Nov 14, 2008 | 1990 Ford F150

Not finding what you are looking for?
1990 Ford F150 Logo

735 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...