Question about 2000 Oldsmobile Intrigue

1 Answer

I put a new rear brake rotor,brake drum on the rear and got it stuck on the emergence brake shoes .How cane i get it off ?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 40 Answers

Back off the adjustment on your "E" brake but remember to readjust it .

Posted on Jun 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Burning smell brakes


Most people do not remove the rear rotors and inspect the Emergency Brake shoes. These often peel off the metal backing on the shoe and jam inside the interior Drum of the rotor. Some people will hear a rusty grinding noise after pulling away from a stop.

These brakes have the old "star-wheel" adjusters and may need to be adjusted more loosely to remove the rotor. Its a bad system in my opinion; the drum always rusts and corrodes and the Ebrake shoes are banana peel thin. With corrosion, the drum acts like a grinder and chews up the brake shoes. Some other configurations use a mechanical link on the caliper to make the service brakes act in an Emergency. It will override a hydraulic failure, but you still need good pads on the caliper.

Mar 17, 2014 | 2000 Ford Expedition

Tip

Removing rear rotors


On the rear wheels, the inside of the rotors act as a drum for the emergency brake shoes. You must loosen the emergency brake so that the shoes back away from the inside walls of the rotor. Loosen the emergency brake, left and right side, by loosening both nuts at the emergency brake handle. Further, the emergency brake's internal adjusting nuts are accessible through the lug holes in the hub. Then remove the rear rotors

on May 19, 2008 | 1987 BMW 5 Series

1 Answer

Emergency brake adjust


the park brake may have to be adjusted separately. if you have disc rotors on the rear . If drums then you will have to adjust the brake shoes up manually to start with

Dec 30, 2013 | 2005 Buick LaCrosse

1 Answer

Emergenct brake will not hold


The linkage could need to be adjusted. Or the brake shoes inside the rear drums are worn out and need to be replaced. If you accidentally drive the brake on. It doesn't take long to wear those brake shoes out. You can normally smell them when that happens. On today's vehicles they are actually designed with 3 different brake systems. Front brake disc and rotors, rear disc and rotors, and inside the rear brake rotor their is a small brake drum where the emergency brake shoes are located. The only purpose for the shoes and drums is emergency brake only (normally). Hope this helps.

Nov 27, 2012 | Cars & Trucks

1 Answer

1999 F250 4x2 - was stored for 3 months and when I tried to move it - the right rear wheel turns but the left rear wheel won't turn. Took off the brakes and caliper - still won't move. I can move...


Hello, The rear rotor has 2 sets of brakes on it. The other thing is to look for slight movement in the driveshaft when it clunks. Depending on the rearend, some have to have both rear wheels off the ground to turn each side. And of course the trans in Neutral.

With the rear wheel you have an Emergency brake and a drum brake inside the center of the Rotor.
The rear of the brake backing plate has a rubber plug which is covering the Star-wheel adjustment for those drum brakes. You can try to loosen the Star-wheel to disengage the Emergency brake shoes. You can try pulling the brake cables toward the cab, to loosen the cables.

If this does not help, your Emergency brake shoe probably rusted off the brake mount and is jammed inside the drum. The linings fall off the metal like banana skins. I can tell you that if the Emergency brakes are a State safety requirement, you need to consider new rotors because the drum portion is usually trashed with rust.

I hope my Solution is very helpful to you.

Jun 11, 2011 | 1984 Ford F 250

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

How to change back brakes 1999 ford windstar, back brakes are grinding, brake light on


does it have rear disc brakes or drum brakes, if disc brakes should be changed just like the front and you might have an emergency brake shoe inside the rotor that they call a halo shoe, if it is drum brakes take off the adjusting spring and the return spring remove the brake adjuster,the the brake bar then remove the brake shoe hold down spring by holding the pin from the back and pushing and turning the spring to remove from the pin, you might have to remove the the emergency brake bar from one shoe by removing the horseshoe clip from the pin on the shoe if you have problems putting it back together look at the other side that you have not torn down yet.

Aug 12, 2009 | 1999 Ford Windstar

2 Answers

How can adjust the emergency brake for my 2004 GMC Envoy...


YOUR MOST LIKELY PROBLEM IS IN THE REAR ROTORS. THE PARK BRAKE AREA WILL RUST INWARD WEARING OUT THE PARK BRAKE SHOE. THE ADJUSTER IS UNDER THE ROTOR ALSO. ONE ON EACH SIDE.

ADJUST THE SHOE OUT UNTIL IT TOUCHES THE DRUM AND THEN BACK IT OFF ABOUT 6-7 CLICKS.

Jul 12, 2009 | 2004 GMC Envoy

2 Answers

Emerg. Brake Drum Removel on E450 .


The park/emerg. brakes should be integrated with the rear brake rotors. To replace them involves removing the calipers and brackets. You should be able to slide the rotors off. You may have to back the park brake shoes off with the shoe adjusters to remove the rotors due to the rust lip that often develops within, but they should slide off once freed. Hope this helps.

Dec 05, 2008 | Ford F-450 Cars & Trucks

3 Answers

Rear brakes on 2005 F150


You can't remove the rotors because the emergency brake is tight on the inside of the rotors. Make sure it's not engaged when you are working on the rear brakes. Block the front tires for saftey. Then you have to remove the rear calipers from the mounting brackets, there are two bolts that hold the calipers on. Make sure you hang the calipers securily with some wire so you don't damage the rubber brake line hose. Then you need to adjust the emergency parking brake shoes in order to remove the rotors. Theres a rubber plug on the backside of the rear hubs, once you look at the back of the hub you'll see the plug. It's on the top. Once you take out the plug, you need to use a screw driver to turn the star spindel. You need to turn the star spindel counter-clockwise in order to give yourself enough clearance to remove the rotors. The beauty of this design is that ford incorporated a drum and caliper system together, but it's difficult to take off the rotors if the emergency brake shoes are to tight. The inside of the rotors acts as the drums for the emergency brake system. I've done this and it's not that hard, but, I did have to replace the emergency brake shoes because they were worn out and the shoes fell off the metal backing plates when I finally got the rotors to come off. They only glued these shoes onto the backing plates, they don't rivet them so take your time getting the rotors off or you can damage the emergency brake shoes, but if you do they are cheap at napa. My service guide says to install the new rotors, use a couple of lug nuts to hold it on, then adjust the star spindal for the emergency brake all the way clockwise until you can't turn it anymore, then you must back it off 8 clicks counter-clockwise. Make sure the emergency brake is not engaged when you are doing this, the 8 clicks backwards compensates for when you do engage the parking brake because the shoes expands outwards. This adjustment sets the emergency brakes so they work properly. Once the emergency brake is properly set you can't remove the rear rotors, which is what your initial problem is. Then install the rubber plug back in the hole, put on the new pads and calipers and you're good to go.

Jun 25, 2008 | 2005 Ford F-150

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...