Question about 2002 Ford Explorer

1 Answer

Cold air comes out driverside but not passenger side

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 45 Answers

If it has dual climate control -- drivers and passenger temp control-----
it could be a temp blend actuator, if it has only one temp adjustment,
it could be a door concern inside the plenum behind the inst panel.

Posted on Jun 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater/Defrost issues


sounds like your flaps are open.

Sep 30, 2013 | 2004 Chevrolet Impala

1 Answer

One side hot other side cold


if you have dual controls for temperature for passenger and driver, they may be set to different levels, try to push the driverside temp control switch or knob in and this will give driver control over both sides again

Apr 17, 2013 | 1999 Pontiac Grand Prix

1 Answer

How come when i turn heat on. driverside blows hot but passenger side blows cold


talking from experience there can be 2 problems , either the "blend motor" on the driverside of the air register has failed or the door inside the register broke i would say 9 out of 10 the "blend motor" is the problem , on a scale of 1-10 its about an 8 to change the dealer refers to this part as a blend door actuator

Nov 20, 2010 | 1999 Buick Regal

1 Answer

Acblows cold on passengerside but warmon driverside on1999 aurora


Check the vent plumbing under the dash with the fan on high. Just run your hand along the tubes and feel for moving air.

May 31, 2010 | 1999 Oldsmobile Aurora

1 Answer

When a/c on blow cold on passenger side cold and warm on the driver side


this sounds like a bad driverside blend door actuator motor, this controls the door for hot or cold air, theres one for pass/side and one for driverside, this motor is located on heater box under the dash,the hard part is to locate it because there are about 4 of them, you would have to locate them one by one and then move all controls until you find the one that doesnt move and that would be the bad one , hope this help.

May 12, 2010 | 2001 Pontiac Grand Am SE

1 Answer

It has dual heating and cooling. The air is on


sounds like the blend door motor is bad on the driverside, its located on the heater box, here a diagram to help you locate it.it is on the driverside of the box, heres a picture of it, this is a single zone yours is daul you will see the pass/side motor the driverside i pointed to its location on your car. hope this helps you.bae6268.gif

Jan 27, 2010 | 1998 Oldsmobile Intrigue

2 Answers

The climate control stays hot on the drivers side and cold on the passenger side on all three, defrost , mid and floor . the passengers side will get hot if you raise the temp to 84 or higher. the drivers...


you have a bad blend motor out, has a hole in the vacuum diaphragm look at the heater box under the dash on passenger side when you find the blend door motor pull it off and **** on the end of the vac. motor watch if the lever moves, if it does get it to the max pull position and with your tongue on the end of the pipe hold the vacuum if it releases the arm then the diaphragm is shot, it also could be the hose end is loose, if this is the case cut the end of the hose off and re hook and try it again. if this does not work try moving the lever on the air box and holding it to the hot postion, if it does not get hot then Your blend door might not be working. Post here if you need more help.

Nov 29, 2009 | 1999 Buick Park Avenue

Not finding what you are looking for?
2002 Ford Explorer Logo

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...