Question about 2003 Ford Crown Victoria

1 Answer

Map and vanity lights do not work. glove compartment light does not work also, 2003 crown victoria lx sport. Every other interior light works.This I think is important; when any door is open all lights are on but vanity mirror lights don't work at-all nor glove compartment. When i click map/reading lamps front or rear the light goes out when the a door is open, when doors are closed the lamps do not work when click on them.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 35,669 Answers

The lamps could be defective or there could be a defect in the lighting control module.

Posted on Jul 13, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
gforce3s
  • 31 Answers

SOURCE: i need a diagram for a 1998 ford crown vic interior fuse box

here ya go

463d1df.gif

Posted on Dec 11, 2008

  • 1 Answer

SOURCE: 2003 Explorer door ajar light stay on when all doors are closed

I had this problem on my 2003 explorer and took WD40 and gave the lock mechanism a good dose where it meets the clasp on the door jam. Then open and close the doors a couple of times to get them working. They get gummed up and sometimes have a tendency to stick.

Posted on Feb 18, 2009

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 10 Answers

SOURCE: Drivers door power window control stopped

Since it is only happening on the drivers side door to multiple switches and lights on that door only, I think the problem is the wiring harness as it enters the drivers door by the door hinges.

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse/s for the map lights and dome lights


ANSWER by patrick mannion on June 01, 2010
Looking at a wiring diagram the dome light and rear reading lights operate through the body control module. Check the BCM 2 fuse, BCM 1 fuse and BCM cluster fuse they may all be in the circuit. These fuses are in the engine compartment fuse box.

Dome glove box trunk vanity map lights all out 2003 Saturn L300

Aug 05, 2015 | 2003 Saturn L-Series L300

2 Answers

2008 ford explorer light control module


Hi Rich , what lights are you talking about ? Exterior Lighting , Interior Lighting ? It doesn't matter All lights are controlled by SJB smart junction box ! An you can't just stick in a used one , It will need to be programmed ! Interior Lighting The interior lighting system consists of the following components:
  • Smart junction box (SJB)
  • Dimmer control switch
  • Interior/map lamps
  • Cargo lamp
  • Glove compartment lamp
  • Vanity mirror lamps
  • Door ajar switches
  • Puddle lamps
The interior lighting system consists of 2 subsystems:
  • Courtesy lamps
  • Demand lamps
The courtesy lamps are controlled by the SJB. The courtesy lamp subsystem consists of the interior dome lamps, the puddle lamps and the overhead console lamps (if equipped). The SJB supplies voltage to the courtesy lamps when the SJB receives the required input.
The demand lamps are controlled by the SJB. The demand lamps subsystem consists of the glove compartment lamp, all map/reading lamps, and the left and right vanity mirror lamps.
The SJB supplies power to the interior lighting system. The SJB will set DTCs if certain circuit failures exist with the interior lighting system.
Exterior Lighting Headlamps
The headlamp system is a dual-beam pattern system. It consists of a low and high beam, with a replaceable bulb. The headlamp assembly has the park/turn indicator lamp integrated into the headlamp assembly. The smart junction box (SJB) supplies voltage to the headlamps when demanded.
Principles of Operation
The SJB receives inputs and delivers outputs to a majority of the electronically-controlled features of the vehicle. The SJB constantly monitors the systems under its control and reports a concern in the form of a DTC. The DTC can be retrieved with a scan tool through the medium speed controller area network (CAN) communication network.
NOTE: Prior to the removal of the SJB, it is necessary to upload the module configuration information to the diagnostic tool. This information must be downloaded to the new SJB after installation. For additional information, refer to Section 418-01 .

Feb 25, 2015 | 2008 Ford Explorer

1 Answer

Interior lights dont work


check the fuses.
what interior lamp , name one, there are like over 25.
doom, dash,park, idiot, blinker, vanity. glove, cig , etc.

Dec 02, 2013 | 2003 Honda Pilot

1 Answer

Trunk cargo light not working after LED installed....


The SJB supplies power to the interior lighting system. The SJB will set DTCs if certain circuit failures exist with the interior lighting system.
Visual Inspection Chart Mechanical Electrical
  • Courtesy lamps
  • Map lamps
  • Luggage compartment lamp
  • Vanity lamps
  • Glove compartment lamp
  • Smart junction box (SJB) fuse 3 (15A)
  • Circuitry
  • Courtesy lamps
  • Map lamps
  • Luggage compartment lamp
  • Vanity lamps
  • Glove compartment lamp
  • SJB

Check fuse # 3 SJB

Jul 07, 2017 | 2010 Ford Fusion 2.5

1 Answer

Battery Draining on 2003 Chrysler 300M


Are you sure that all interior lights go off? Make sure the vanity mirrors actually go off when the doors are closed. Glove compartment light, map lights. Some had center console lights. Check for a short at the cigarette lighters. Use an ohm meter and check for continuity to ground at supply wires.

Jun 08, 2017 | 2003 Chrysler 300M

1 Answer

Fuse blown for interior dome light. which fuse and location?


The manual states the fuse location # for interior lighting is 18 and the amp is15a. I am showing 18 is from far left bottom corner it is the second fuse going up.

Dec 12, 2010 | 2007 Ford Crown Victoria LX Sedan

1 Answer

My boot light is not working and the bulb is fine where is the fuse for this?


F99 Mini 10 Red Luggage compartment light, footwell lights, puddle lights, vanity mirror lights, interior lights, aircon control unit, roof console unit.

See:-
http://www.brendastuart.co.uk/xtype/central_fusebox.htm

Feb 02, 2010 | 2003 Jaguar X-Type

1 Answer

Knocking noise from rear passe ger side 2003


Your axle bearing is more than likely shot. The right side goes out first for some reason. Fairly inexpensive if you can do it yourself.

Jul 09, 2009 | 2003 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...