Question about 1984 Mazda RX-7

2 Answers

Clutch Problems with my rx7

When i was driving my 1984 mazda rx7 GS I was slowing down and the clutch pedal went to the floor and would not come back up and the car refused to move and i have no clue as to what is wrong with it

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

More than Likely your clutch reservoir is low on fluid and has leaked all the fluid out so check that first if the reservoir is empty then fill it with brake fluid. Then it will need to be bleed if you don't know how it would be better to take it to a mechanic. Let me know if you want to try it and I will help you.

Posted on Jun 01, 2010

  • keeno782 Jun 02, 2010

    Well it isn't that, the clutch fluid level is still in the middle, but i was looking at it and the fluid level has actually dropped a little in the past couple hours

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

If your fluid level is good then the seals in your master cylinder or slave cylinder have gone bad. I have had 2 of these cars and the slave went on both. Luckily the slave is the easier one to swap out. Neither are very difficult to replace and they are not very expensive. Also, check out the hose that goes to the slave cylinder, after 25+ years they can start to rot out.

Posted on Dec 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Mazda MX6 Clutch pedal has no push back from floor but still shifts


I am not a mazda guy but it sounds like the pressure plate is bad. Have you check the clutch linkage to be sure something did not slip or break. If so I would be looking at the clutch pressure plate.

May 18, 2017 | Mazda Cars & Trucks

1 Answer

Clutch pedal was ok, 84 Ford F150 4x4 351 W w/4speed, then went to the floor?


Sounds like the slave cylinder went out. If it's inside the bell housing...do a complete clutch job while you are at it.

Jun 06, 2012 | 1984 Ford F 150

1 Answer

How do you bleed the hydraulic clutch on 1984 944


924 has cable operated clutch. When the cable on mine broke pedal went straight to the floor, hydraulic usually much slower to get to floor. Cable is an easy replacement. bleeding hydraulic usually done from nipple on slave cylinder (near release arm on clutch housing.

Feb 01, 2018 | 1984 Porsche 944

2 Answers

My 1991 rx7's clutch went so loose that it actually stuck to the floor and the car died. it started drove awhile then repeated the problem. now it won't start; seems like it has no compression


Fixing the clutch, I bet one of the lines had been leaking clutch fluid for quite a while. May top it off, and have a friend stomp down on the clutch to see if you can find the leak and repair it, then make sure to bleed your clutch back off. BTW, do you mean no compression as in the clutch has completely gone, or the engine has lost compression?

Jan 17, 2011 | 1989 Mazda RX-7

1 Answer

My 1984 rx7 starts when choke is pulled out. WHen


Your carberater is having problems getting the correct amount of fuel.Either a line or fuel filter is clogged or you need to have your carb. rebuilt.

Apr 26, 2010 | 1983 Mazda RX-7

1 Answer

Clutch problems


if the clutch is still working then it could be the clutch spring which has come off or snapped because it is very old. some cars have hydraulic clutch systems but i would think that yours is a spring. look in the footwell up the pedal and you may see a spring which has come off.

Apr 04, 2009 | 1984 Ford Mustang

2 Answers

Need fuse block Layout for 84 RX7


www.edmonds.com they carry owners manuals online and should have one for your car as well

Mar 19, 2009 | 1984 Mazda RX-7

1 Answer

I have an rx7 series 6 twin turbo manual transmission. When I pump the clutch pedal while engine is running the pedal eventually ends up flat on the floor and doesnt return unless physically pulling up...


Asuming its a "normal clucth", im no "RotaExp". ill say release-bearing or springs=New clucth house.
But "pumping" realy just sounds like a very BAD idea...;)

Sep 27, 2008 | Mazda RX-7 Cars & Trucks

Not finding what you are looking for?

Open Questions:

1984 Mazda RX-7 Logo

451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...