Question about 2003 Saturn VUE

1 Answer

Torque for axel nut on front wheel hub? - 2003 Saturn VUE

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 749 Answers

151 ft lbs or 205 nm for front wheel drive only the awd is 81ft lb or 110 nm.

Posted on Jun 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy malibu torque hub bearing front axel


about 80 lbs is sufficient ,if the wheel still can moved top to bottom then then renew the bearing ,and check the ball joints on the lower track control arm

Jan 17, 2015 | 2000 Chevrolet Malibu

1 Answer

What is the 2005 kia rio front axel nut torque ???


Hi,
for the front hub its 157 - 235 Nm.

Sep 20, 2014 | 2005 Kia Rio

1 Answer

Replacing axel on passenger side of 2000 hyundai elantra please give a step by step


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Front wheel
    • Spindle nut
    • Wheel speed sensor, if equipped
    • Outer tie rod end
    • Stabilizer bar link
    • Lower ball joint
  3. Press the stub shaft out of the hub.
  4. Pry the inner joint out of the transaxle or intermediate shaft.

To install:

NOTE

Use new circlips, split pins and self-locking nuts for assembly.


  1. Install the inner joint so that the circlip is felt to seat in the retaining groove.
  2. Guide the stub shaft into the hub.
  3. Install or connect the following:
    • Lower ball joint and torque the nut to 43-52 ft. lbs. (58-70 Nm)
    • Stabilizer bar link
    • Outer tie rod end and torque the nut to 17-25 ft. lbs. (23-34 Nm)
    • Wheel speed sensor, if equipped
    • Spindle nut and torque the nut to 144-187 ft. lbs. (195-253 Nm)
    • Front wheel
  4. Check and/or adjust the wheel alignment.

Jun 16, 2011 | 2000 Hyundai Elantra

1 Answer

I need to know how to take off an axel on a 1992 plymouth laser front wheel drive and a 5 speed


In general, on front wheel drive axle replacement, the method is as follows: raise and support vehicle and remove wheel, remove the axle nut (located in the center of the hub assy.), remove the nut retaining the lower ball joint and separate from the lower control arm, remove axle from wheel hub and suspend the hub to one side, use a pry bar to force the axle out of the trans-axle, reverse process to install and observe all torque specifications.

Feb 08, 2011 | 1992 Plymouth Laser

3 Answers

How to replace a front wheel hub assembly on a 1999 blazer 2wd


remove tire
remove axle nut
remove 3 bolts holding hub in
sometimes may need to hit hub with hammer after all bolts out to get it to release

Dec 22, 2010 | 1999 Chevrolet Blazer

1 Answer

Front wheel bearing assembly unit, what tools will i need? size sockets ext the right foot lbs of torque for the axel nut,


TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Mar 16, 2010 | 1999 Oldsmobile Alero

Not finding what you are looking for?
2003 Saturn VUE Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...