Question about 2001 Hyundai Tiburon

1 Answer

The cluch gose in very easy and will not shift unless car is off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

Could be that you have a fluid leak on your slave cylinder to the clutch. You need to first check the clutch fluid res. out under the hood. Look for a small white res. close to the firewall. You can use DOT 3 brake fluid to refill if it is low. Once you have refilled it check for clutch peddle travel. Be sure to check for a leak under the car. Keep a check on the fluid res. to see how quick it leaks down.

Posted on Jun 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Its a stick shift so must put cluch all the way to the floor to start it did this one other time a week ago i pumped the cluch in and out acuple times and it started now i did that a bunch with the cluch...


There is a safety switch on the clutch pedal-it is called a clutch interlock switch. Unless the clutch is depressed (so the switch is on), the power won't pass from the key switch to the starter to start the car. Check your clutch safety switch. It will be up high on the pedal, or mounted close to the pedal so the pedal operation will actuate the switch. It may be defective, or it may have slipped out of position.

Nov 27, 2013 | 2001 Hyundai Santa Fe

1 Answer

How to replace the cluch return spring


Transmission has to be taken out of vehicle

Nov 29, 2012 | 1996 Nissan Pickup

1 Answer

We just bought a 2000 Suzuki esteem, the problem is whenever we start the car, it becomes very difficult to shift between gears when the car is idle, but when the car is on the freeway, shifting works...


The cluch not fully disingaging , ( carpet under the pedel, pedel bent , bushing worn out of pedal, low on fluild in clutch master ( brake fluid ) and bad cluch master or slave or air in system. A damaged clutch will drag too. If it shifts OK with the car shut off standing still trans lube is likly OK too. If it has a clutch cable it may need to be adjusted pull up on the clutch pedal as high as it can go then pust down with your hand it should only go down an inch before it gets harder to pust down as it openes the clutch and shoul continue to go down about 4 or more inches. The pedal should be as high or a little higher than the break paedal. If not the pedal height may be needing to be adjusted higher. Some slave master hydrolic sysems aren't adjusted and have to be replaced to fix lack of enought movement Clutes that are hard to pust in or get much harder as you get closer to the floor the cluch is likly to be worn out and need to be changed with a new clutch kit and resurface the flywheel. The flywheel can change to unflatand the cluch can drag. engine oil getting into the clutch though a leak in the valve cover or rear main can get on the cluch and make it drag and grab.

Mar 21, 2010 | 1996 Suzuki Esteem

1 Answer

Hard shift into any gear after clutch pressure loss No previous problem with shifting prior to this , with good clutch pressure and smooth shifting into all gears.


clutch plate is worn out cluch is good just needs cluch plate but you might as well buy the clutch kit and change it all to avoid future problems

Dec 22, 2009 | 1993 Saturn SL1

3 Answers

88 Toyota Pickup, has become difficult to shift in to gear. Once in gear (1,2,3,or4th) very smooth. I believe must be something up front in the clutch linkage. Possibly? Can get into, but takes awful...


if your linkage was bent it wouldnt shift into all gears easily.sounds like you need to blead your slave cylinder to your clutch.10mm wrench and bleed it like your brakes same type set up.

Nov 24, 2009 | 1988 Toyota Pickup

1 Answer

2002 hyundai accent my cluch peddel goes soft


check fluid level if low bleed out the system.If thats fine then you have slave cylinder Problem.Before Changing the cluch assembly check your master cylinder is pushing good pressure.

Jul 17, 2009 | 1998 Hyundai Tiburon

1 Answer

1987 porche 924 cluch problem


Hi. your pressure plate is going bad at this time. you will need to replace this part asap.

May 23, 2009 | 1987 Porsche 944

1 Answer

Cluch won't dis engage


How long have you had your car? How many miles on it?

Maybe the clutch plate gone, if the plate is not thick enough, you won't change the gear.

Jul 06, 2008 | Mazda MX-5 Miata Cars & Trucks

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...