Question about 2000 Chevrolet S-10

1 Answer

How to replace an ignition switch 2000 chevy s10

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 447 Answers

You need to remove the upper and lower steering column covers and you'll find the switch beneath them. Covers are held in place by screws [torx head I believe] that come in from the bottom. They aren't real obvious so don't force anything to come apart. I see a few of these switches fail and usually they cause a group of items to quit working such as the blower motor or part of the dash or you may get erratic dash indicator lamps that come on and go off. You shouldn't have to remove the steering wheel unless you are removing the actual key cylinder itself. Once you get to the switch check the connector for any discolored or melted areas. If you find any you may have to replace the harness end [pretty rare though] Good luck!

Posted on Jun 02, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: installing ignition switch for 87 chevy s10 Blazer 2.8L 4X4

you need to replace the electrical part of switch?If os it is down on column under dash will be two bolts holding on with the dimmer switch also

Posted on Aug 28, 2008

  • 199 Answers

SOURCE: 2000 chevy s10 starting problem

there is a solinoid that enguages the starter it is stuck tap the round cylinder that is atached to the top of the starter it should disenguage the solinoid if not try to hit it harder. dont beat it up though. it also may need a new starter.

Posted on Jul 17, 2009

  • 541 Answers

SOURCE: how do you replace an ignition starter switch on a

it is on the top of the steering column in the truck cab.remove battery cables. remove the lower portion of you dash.loosen the bolts on the plate that holds your column up to the dash. the column will pull down some. you may have a gear indicator tab/string that needs to be undone. remove column clamp blots all the way. the switch is on the top, it has a rod that moves and is postioned on the column. remove old switch, install new switch in th position where the old on was

Posted on Oct 23, 2009

  • 2309 Answers

SOURCE: got a 2000 chevy 3500 express van how do i get the

remove the steering wheel , need a puller and locking ring tool, disconnect batt, turn the key to tho on position, and remove bolt that holds the tumbler in,

Posted on Nov 13, 2009

roniecon
  • 6826 Answers

SOURCE: i have a chevy 2000 s10. where is the neutral

It is on the shift shaft,on the transmission,it is not to bad to change out.

Posted on Jun 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram for the ignition switch on a 2000 chevy s10 ?


Unfortunately, you will not be able to do that. The key and tumbler are an intricate part of the vehicles "anti-theft system. If the ignition switch or tumbler is broken it will have to be replaced and the theft code relearned. When the key is turned in the tumbler, the switch reads the key code and sends the code to the BCM. The BCM verifies the code is correct and sends a start message to the ECM and allows the engine to start. With out that code verification, the engine will not start.

Aug 28, 2014 | 2000 Chevrolet S-10

1 Answer

How do I find the blower resistor on a 2000 chevy S10 pickup


Here's what it look's like,it's located next to blower motor,remove electrical connector and two screws and ala,it's off.

Jan 31, 2013 | Cars & Trucks

1 Answer

2000 chevy s10 ex cab 2wd has leaky lines by


These are oil cooler lines and there are 2 sets of 2 and should be replaced, Fairly easy but messy. If one blows apart you run the risk of causing severe engine damage.

Mar 01, 2010 | 2000 Chevrolet S-10

1 Answer

I have 98 Chevy S10 pick-ups? MY problem is there


Yes it could well possibly be the ignition switch or starter solenoid or intermittent ignition switch starter contact.Again check connections on battery especially the ground connection at the block.Also there could be air in the fuel line any of these could be hindering start up!

Oct 02, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

2000 Chevy s10 2.2L very rough idle at low rpm


run a fuel pressure test, if that checks out fine it may be a faulty coil pack or ignition control module

Jul 28, 2009 | 2000 Chevrolet S-10

1 Answer

2000 chevy s10 starting problem


there is a solinoid that enguages the starter it is stuck tap the round cylinder that is atached to the top of the starter it should disenguage the solinoid if not try to hit it harder. dont beat it up though. it also may need a new starter.

Jul 17, 2009 | 2000 Chevrolet S-10

1 Answer

1988 chevy s10 blazer 4.3, cut out , will srart but will not stay


Your vehicle as an ignition control module located on top of the distributor (under the cap and rotor) I would pull the ICM and take it to NAPA and have it tested if bad replace it (cost about $80). Sounds like a ICM problem or it could be the ignition switch located on the steering coloum which can't be tested but costs $20. Hope this works

Jul 15, 2009 | 2000 Chevrolet S-10

1 Answer

2000 Chevy s10 starting problem


Check the ignition and Engine relay switches located under the hood. Sometimes relays go weak with age and even a bump on the road will shut them off. If you can turn the truck on, take it to Autozone or similar store for a free DTC scan code.

Jan 09, 2009 | 2000 Chevrolet S-10

3 Answers

I have a 97 Chevy S10 pickup...cannot move shifter out of park


When my battery was dead i was forcing the key in the ignition which messed everything up with my chevy s10 and have to get everything replaced....: (

Dec 28, 2008 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

2,242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...