Question about 2000 Daewoo Lanos

1 Answer

How to install ABS

I have a bought a daewoo racer 1996 model ( made in Korea) and have installed bumpers and lamps of 2009 Nexia. I have purchased a second hand ABS system of Daewoo. It has one circut ( like EPU or chip like computer), ABS unit with compete wiring connected with each other and beak lines for breask survey and wheels. The is one outlet or a grip of connection which i was not able to figure out. It has four pins. My idea is that it is the point which could be for electric power or to be connected with main car chip i am not sure. Can anybody help me out how to install it with any diagram etc.

Posted by on

  • 1 more comment 
  • yadayada
    yadayada Jun 01, 2010

    THIS WILL COST MORE THAN THE CAR IS WORTH.

  • syed_sohail_ Jun 02, 2010

    Thanks for the comment. Let me clarify it a little bit more. This Daewoo is 1.5 with a similar model launched in other countries as Daewoo Lemans. I have bought the second hand ABS system for $75 and it has all sensors, wheel hubs (front and back), rings, ABS unit, electronic chip with complete wiring. However, there is only one "white color" outlet grip having four pins which i was not able to figure out. If you have any material or diagram of the connection i can work it out fine and let you know as well. I will pay $ 20 to the electician and mechanical expert to help me out while installtion which they have agreed.

  • yadayada
    yadayada Jun 02, 2010

    good luck

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,857 Answers

Your best bet is to go to mitchell1diy online to try to figure it out. Pay the ten bucks.

Posted on Jun 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get highest mileage in Daewoo racer 1993?


Run only downhill,lol. Free up intake and exhaust, remove any unneeded engine accessories, install arrow dynamic improvements, run tires inflated as much as safe, stop dragging that boat anchor!

Jan 13, 2015 | Daewoo Cars & Trucks

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

1 Answer

Do I have to remove the tray liner from the 2003 Rodeo pick up to replace tail light assembly?


Utility And Sportside Pick-Up Models
  1. Make sure the headlight switch is off and the ignition switch is in the lock position.

  2. Unfasten the screws retaining the lens, then remove the lens.

  3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

  4. Remove the bulb from the socket.

  5. Installation is the reverse of removal.
    Without A Step Bumper

    1. Make sure the headlight switch is off and the ignition switch is in the lock position.

    2. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

    3. Pull the bulb from the socket.

    4. If necessary, remove the lens retaining clip and the lens from the filler panel.

    5. Installation is the reverse of removal.
      With A Step Bumper

      1. Make sure the headlight switch is off and the ignition switch is in the lock position.

      2. If necessary, lift the lamp up and tilt the bottom away from the bumper to release the lamp retainer.

      3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

      4. Pull the bulb from the socket.

      5. If necessary, remove the step bumper pad, the screws that attach the lamp to the bumper and remove the lamp assembly.

      6. Installation is the reverse of removal. Tighten the lamp assembly-to-bumper screws to 14 inch lbs. (1.6 Nm).

Dec 12, 2010 | Isuzu Pickup Cars & Trucks

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

3 Answers

My daewoo racer eti 95 model, while driven i had experience that the engine stop 2 time, the i had restart its ok it starts,upon continuing driving about 15 kilometers travel the engine stop, when i starts...


You don't say what you are doing when the engine stalls. Are you stopped in traffic? Maybe the idle adjustment is too low. Maybe you have bad gasoline. No fire in the high tension cable means no spark? But the car would never run without firing. Maybe one spark plug is fouled, and you're running on three cylinders some of the time. Then you would notice a power loss from the engine, too.

Nov 25, 2009 | 1999 Daewoo Nubira

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

Why is nexia not in list of daewoo models


http://en.wikipedia.org/wiki/Daewoo_Cielo

Also called Daewoo Cielo, Daewoo Heaven, Daewoo Nexia, Daewoo Racer, Daewoo Super Racer

Feb 02, 2009 | 1999 Daewoo Nubira

2 Answers

Daewoo racer gti


Hi Gracieland,
I found a manual on CD for my Daughters 99 Daewoo Lanos on ebay motors cars/trucks... type in 99 daewoo lanos manual and it should bring up some.
Hope this helps.
Sallycna@msn.com

Jan 29, 2009 | 1999 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...