Question about 2006 Saturn L300
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2001 tahoe door panel
THE COUTESY LAMP IS HOT DUE TO THE DOOR BEING OPEN WHILE THIS PROCEDURE IS DONE!!!! First: Remove the triangle panel at the top of the door (behind the mirror). This is held in with two metal clips about half way down the panel. Do not pry at the bottom as there are two tabs that slide in to keep the module in place. I pulled the top of the triangle out by hand then could see the clips and used a straight screw driver to carefully pry from under the triangle panel so as not to scar the visible part after re-assembly. Once these two clips are disengaged the triangle should pull straight up and be free. Second: Carefully pry out the door lock insert. There are no significant tabs to worry about here. Again a straight screw driver and care should not leave any scars. The lock insert has no mechanical connection but simply is used to slide the lock rod. Re-installing you will need to align the slot for the rod in the lock or unlock position depending on the rod position. Third: Carefully pry out the insert that is located at the door handle. Start at the rear of the insert as this is where the clips are located and once the rear is out pull open the door handle and pull the insert to the rear so as not to break off the two front tabs. You will find two small screws (mine were black). One near the front and one at the rear of the door handle module. Both are 7 mm and are the only ones that need to be remove in the process. (I understand some door panels have an other screw at the very bottom of the door as well; guess you'll have to check you door. Fourth: Pry up the control panel for the automatic windows and unplug the wires. Here again start from the rear and once the rear is free pull the module to the rear and it should come free. There are tabs at the front that you do not want to break off. To unplug the wires - First remove the clips (mine were blue) that hold the plug in place. There is also a push catch on the plug that must be depressed to release the plug from the control panel. Fifth: My door had no push in 'buttons' or clips to hold the door panel in place. It simply lifted up and became free with the exception of the numerous wires attached to things like the speakers, the remote mirrow and courtesy light. Unplug these wires by first taking off any retaining clips (usually blue) and then unplug the wires. The courtesy light pulls straight out (toward the front) and watch your fingers as this is one hot little bulb. The door panel can then be totally removed and set aside. You may find it easier to remove the courtesy light lens by prying out the rear first and then pulling it toward the back of the door so as not to break the two front clips. I found it easier to do this and then install the bulb in the lens and then install the lens back in place. Six: I'm sure I don't need to say it but here goes - ' reverse the procedure to re-assemble'. Remember to poke the courtesy light wire out the hole and re-connect the remote mirror and speaker wires before the door is put in place. The wires to the window and electronic lock module can be installed after the door is back in place. Working by myself made the door difficult to handle during re-installation so I took a 'light' bungy cord and placed some protection over the top of the door and hooked the bungy into the opening were the door handle was to come through. This allowed me to steady the door and do the electrical connections as required. PS - we were replacing the power window motor and were able to 'force' the cable into the gears of the new motor by turning the motor and this saved a lot of further disassembly. The contacts on the new motor were reversed so I removed the pins from the plug going into the motor and reversed them - presto.
Posted on Mar 17, 2009
SOURCE: remove door panel
Disconnect your negative battery cable. Locate and remove the screws
that hold your interior door handles in place (they may be hidden by
snap in, or snap on clips). Remove the interior door handles, then
disconnect the wire clips to the switches. Your panel is held in place
by snap in clips; use a small pry bar to pull them from the door (try
to get as close to, or directly under the clips to prevent them from
tearing out of the door panel). Once the clips are pulled, pull the
panel upward to remove it from the door.
Install in reverse.
Posted on May 25, 2009
This may sound stupid, but I will ask anyway.... did you "pull" on it after you loosened it? Been there...
Posted on May 30, 2009
Sounds like a water pump or radiator hose. Need to see exactly where the leak is coming from to confirm which.
Posted on May 31, 2009
Tips for a great answer:
Dec 30, 2015 | 2008 Saturn VUE
Apr 16, 2015 | 2002 Saturn L-Series
Apr 16, 2015 | 2002 Saturn L-Series
Jul 25, 2014 | 1999 Saturn SL
May 19, 2014 | 2004 Saturn L300
Nov 21, 2011 | Cars & Trucks
Mar 09, 2011 | Saturn L300 Cars & Trucks
Feb 22, 2010 | 2003 Saturn L-Series
Aug 10, 2009 | Saturn SL2 Cars & Trucks
May 31, 2009 | 2001 Saturn L-Series
2,271 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: