Question about 1987 Honda Accord

1 Answer

How to replace the bracket for clutch, brake and gas pedal

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 88 Answers

Uuff is a big work, you need to remove all plastic under sterring wheel, it have screws on firewall, need to remove throtle cable, brake link, and clutch cable.

Posted on Jun 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loose clutch pedal brake


THE BRAKE CLUTCH PEDAL BRACKET WILL SOMETIMES LOSTEN UP BECAUSE ITS BENT OR WORE OUT BUSHINGS.LOOK UNDER STEERING WHEEL FOR SLACK OR SLOPPY PIVOT POINTS!!

Nov 24, 2013 | 2001 Ford Ranger Regular Cab

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

1 Answer

Car will not accelerate when gas pushed


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

When you put the clutch in the brake goes in to


You're going to have to sit in there with your head on the floor and feet on the seat and look under the dash and the clutch and brake pedals.
Last time I was under a ford dash there was a large pin welded in the middle of a bracket. half the pin in the inside of the braket was where the brake pedal hung from and the half on the outside was where the clutch hung from. The pedals are suposed to have bushings in them. Perhaps a pedal froze on that pin and the pin broke free from the bracket.

You're going to have to look to know for sure.

Aug 31, 2011 | 1985 Ford Bronco II

1 Answer

BRAKE LIGHTS COME ON WHEN CLUTCH IS DEPRESSED


The bracket that holds the pedals becomes loose sometimes, letting the brake move slightly when you press the clutch. Check for that movement, there is an adjustment for the brake switch, the switch is on the brake pedal under tha dash. It can be pushed in or out which ever is necessary to get the brake lights off.
Randy

Nov 10, 2010 | 2002 Jaguar X-Type

2 Answers

How to adjust clutch pedal on 86 mustang lx


clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


REMOVAL & INSTALLATION


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

Put a new clutch cable on my escort but no good as i can not adjust the pedal


LIFT THE CLUTCH PEDAL TO DISENGAGE THE ADJUSTING MECHANISM.THIS MUST BE DONE DURING CABLE INSTALLATION AS FAILURE TO DO SO WILL RESULT IN DAMAGE TO THE SELF ADJUSTER MECHANISM.INSERT THE CLUTCH CABLE THROUGH THE DASH PANEL AND THE DASH PANEL GROMMET.( WARNING ) BESURE THE CLUTCH CABLE IS ROUTED UNDER THE BRAKE LINES AND NOT TRAPPED AT THE SPRING TOWER BY THE BRAKE LINES IF EQUIPPED WITH POWER STEERING ROUTE THE CABLE INBOARD OF THE POWER STEERING HOSE.PUSH THE CLUTCH CABLE THROUGH THE INSULATOR ON THE STOP BRACKET AND THROUGH THE RECESS BETWEEN THE PEDAL AND THE GEAR QUADRANT.LIFT THE CLUTCH PEDAL TO RELEASE THE PAWL ROTATE THE GEAR QUADRANT FORWARD AND HOOK THE CABLE INTO THE GEAR QUADRANT.INSTALL THE CLUTCH SHIELD ON THE BRAKE PEDAL SUPPORT BRACKET.ON THE TEMPO OR TOPAZ INSTALL THE PANEL ABOVE THE CLUTCH PEDAL.USING A PIECE OF WIRE CORD OR TAPE SECURE THE PEDAL IN THE UPMOST POSITION.INSERT THE CLUTCH CABLE THROUGH THE INSULATOR AND CONNECT THE CABLE TO THE CLUTCH RELEASE LEVER IN THE ENGINE COMPARTMENT.REMOVE THE DEVICE USED TO TEMPORARILY SECURE THE PEDAL AGAINST ITS STOP.ADJUST THE CLUTCH BY DEPRESSING THE CLUTCH PEDAL SEVERAL TIMES.INSTALL THE AIR CLEANER.

May 31, 2010 | 1995 Ford Escort

3 Answers

Clutch pedal box has snapped off its mounting on vw polo


1-disconnect battery. 2- remove all lower dash plastic panels. 3- disconnect all plugs on steering coloumn. 4- remove shear bolts on steering coloumn, easy with a long 8" sharp chisel (get 2 x new shear bolts £0.50p each). 5-loosen & remove bolt at steering rack in drivers footwell, mark position of spline before removing this makes it east to refit (tipex). 6- pull steering coloumn out towards you & it will slide off the bush quite easy. 7- loosen clutch cable adjustment & remove cable nipple at pedal. 8-remove clutch pedal. 9- pull brake pedal out of plastic insert, this will break there is no way to remove this without breaking the plastic clip. get a new brake pedal clip insert for a Mk 3 golf £4 its the same (dont let VW sell you a new pedal) 10- remove 5 x nuts holding pedal box to bulkhead/brake servo. 11- cut 2 x cable ties holding throttle wiring & disconnetc plug above heater on drivers side. 12- push/pull brake servo slightly out of bulk head. 13- remove pedal box.
Cause of the problem- The clutch bracket is only held to the pedal box with 2 x spot welds & a 10mm tack on the top corner.
Repair- Fully Weld the clutch bracket to the pedal box. Great repair.
refitting reverse of above.
Duration around 6/8 hours Less if you get the spare parts before you start.
I wasted time trying to remove the brake pedal without breaking the clip impossible to do even with theVW tool. £4 on a new clip is well worth it.

Jan 30, 2010 | 2000 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...