Question about 2006 Toyota Sienna

1 Answer

I changed the brake pads and rotors. After

I changed the brake pads and rotors. After finishing the job, bled brakes. Once completed, pumped brakes and drove van. The brake light on the dashboard is on, and will not go out.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

Did you foll your brake resiviour? it need to be at full level to turn off the lite. its under the hood drivers side firewall fill it good luck CJ. .

Posted on Jun 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing the rear brake pads and can't compress the piston into the caliper- any ideas? 2003 rendezvous


FIRST REMOVE SMALL AMOUNT OF BRAKE FLUID FROM THE BRAKE MASTERCYLINDER. THEN USE A LARGE C - CLAMP AND LEAVE THE OLD BRAKE PAD IN PLACE ON PISTON SIDE THEN COMPRESS THE PISTON IN CALIPER BORE. IF YOU SEE SIGNS OF BRAKE FLUID LEAKING AROUND PISTON SEAL.THE BRAKE CALIPER NEED REPLACING.WHEN YOU FINISH BRAKE JOB NEW BRAKE SHOES IN PLACE MAKE SURE BRAKE MASTERCYLINDER COVER BACK ON MASTERCYLINER THEN PUMP BRAKE PEDAL UNTIL NEW BRAKE PADS SEAT AGAINST BRAKE ROTOR.CHECK BRAKE FLUID LEVEL IN MASTERCYLINDER MAKE SURE ITS NOT LOW.

Aug 12, 2011 | 2003 Buick Rendezvous

1 Answer

Need to replace brakes on 2000 GMC Safari. does it have disc brakes all around or drum rakse in rear?


Disc brakes in the front and drum brakes in the rear. Make sure that you repack the front bearing's with wheel grease before finishing the job.If the front rotors and or the rear drums have a rough brake pad surface,get them resurfaced before installing new brake pads or brake shoes in the rear. you can go online or your public library for complete instructions on how to replace the brakes on that vehicle.

Apr 01, 2011 | 2000 GMC Safari

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

3 Answers

While driving my 1994 Honda Accord the brakes went out. I can only get the car to stop if I press the brake pedal all the way down to the floor. When the car is shut off and I pump the brake pedal, I can...


There may be air in the lines. Bleed all your brakes starting at the farthest wheel from the resevoir, and finishing at the closest one. Try the pedal after its bled. If the pedal still feels soft or travels to the floor there may be a pinhole leak that may be spraying on the underbody of the car, or the seals in the master cylinder are gone filling the vacuum booster(if equipped). Air compresses more than oil so if bleeding works that may be the problem.

Feb 21, 2010 | 1994 Honda Accord

2 Answers

Brake pedel pushes to the floor


pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Jun 27, 2009 | 1997 Ford F150 Regular Cab

2 Answers

Vauxhall tigra 1996 1400.replaced rear brakes and bled them but the pedal is still soft when braking.


hi. im sure that brake pads are the right reference to your car, but did you cut the disc surface? if you didn´t you must wait until the brake pad surface be in complet contact with the disc surface, meanwile your pedal brake will be to soft because it makes kind of elastic movement in the brake pump. maybe that´s the problem, just wait a few more brakes and see what happens. hope this help you.

May 06, 2009 | Cars & Trucks

1 Answer

Put new rear rotors and pads on my 2002 I35 Infinity, now have very weak pedal , have to pump the brakes in order to stop, doesn't maintain pressure.


Doesn't sound like the brake lines were bled properly. Many times after pad and rotor installation if the lines are bled correctly you will have to pump them initially after the repair for a couple of minutes until the pressure is built back up. Also check the master cylinder and make sure fluid level is ok.

Apr 13, 2009 | 2004 Infiniti I35

1 Answer

Mercedes benz antilock brakes


Hi!
You dont have to disconnect the ABS system to replace brake pads on your vehicle, definatly. Dont forget to pump brake pressure up once your finished
Goodluck!
Carlo@ss

Apr 09, 2009 | 2003 Mercedes-Benz C-Class

Not finding what you are looking for?
2006 Toyota Sienna Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...