Question about 1987 Chevrolet Corvette

1 Answer

Ignition replacement how do you remove the ignition on an '87 vette to replace it???

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Remove the steering wheel & retainers such as the lock plate and cclamp spring using the special tools required.Auto Zone sell that
Them you remove the directional switch to gain access to the screw that holds the ignition cylinder inplace

Pull it out and reinstall the new one

Posted on Jun 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

87 ford bronco replace ignition switch


Lower your steering column by removing the mounting screws located at bottom of dash, remove electrical connectors, tape or find a way to hold metal rod in place, remove switch. Install reverse of removal.
Picture of what your looking for:

10f967bd-36b8-4c67-9524-704df0ec6337.jpg

Dec 07, 2013 | 1987 Ford Bronco

1 Answer

I have 87 vette driven car stop running change module coil still no spark starts ounce in a month then dies had three mechanics look at it and no one knows what wrong with it


car is a classic--get the hole ignition system looked at by a specialist-othr parts are worn or wires cud hav degraded--secure a haynes repair manual etc to study procedures

Jun 03, 2013 | Cars & Trucks

1 Answer

87 f150 driving just quit running now wont start


Do you have spark?? If not replace the Ignition control module (Called the TFI) and remove the distributor and replace the pickup coil inside. Use Motorcraft replacement parts, the aftermarket cheap ones fail really quick, 25 years of experience taught me that.

Jul 13, 2012 | 1987 Ford F 150

1 Answer

Replace ignition 87 4runner


It is probably better to replace the switch.
If it is anything like my 87 4Runner, the switch is pretty worn out anyway. I just replaced the switch wiring harness in mine.
Get a new switch and a Haynes manual at an auto parts store.
The manual describes how to replace the switch.
WAY too much to list here, but pretty simple really.
Good luck :)

Nov 06, 2009 | 1987 Toyota 4Runner

1 Answer

85 vette starts but will not stay running


there is a sensor on the throttle body it' controls the idel of the vehicle it's called a tps and has a electrical lead to it this should be replaced it will be positioned right behind the butterflyplate of the throttle body

Apr 26, 2009 | 1985 Chevrolet Corvette

2 Answers

Replace turn signal bulbs on 2001 corvette


Rears are simply remove the two screws on the lens and remove the tail light from the Vette, twist the connector to get to the bulb. Reverse instructions to install. For the fronts jack up the front, remove the small closeout panel under each side, push the brake cooling duct to one side and twist the bulb socket out of the light to get to the bulb. Reverse instructions to install.
sebring1962@yahoo.com

Feb 22, 2009 | 2001 Chevrolet Corvette

3 Answers

94 vette running rich andslight miss


check intake manifold for leaks and also inspect all vacuum hoses also may be good idea to replace opti spark ignition module its located on the coil mounting bracket at front of right cylinder head if its been exposed to water , antifreeze, or moisture it can effect ur cars timing

Nov 30, 2008 | 1994 Chevrolet Corvette

1 Answer

89 vette


The ignition module inside the distributor may be the problem. Get a new one and try it out. The modules from GM are more dependable than aftermarket ones. If that is not the problem, it's nice to have a spare module in case of an emergency failure.
Squido

Oct 15, 2008 | 1989 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...