Question about 1987 Ford Bronco II

1 Answer

Having trouble start have to hold the accelerator pedal to the floor?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

If it is carbureted,then the carburetor needs rebuilding most likely,and replace the float in the caburetor also.

Posted on Jun 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i fix acceleration problem in 08 altima car?


What are the trouble codes? There are several sensors that could cause this problem. Maf, tps, map, accel pos...
Could also be a wiring issue.

Aug 06, 2017 | Nissan Altima Cars & Trucks

Tip

How To Check & Reset Your 2002-2006 Nissan Altima Service Engine Soon (SES)...


The following directions will help you decode your 2002-2006 Nissan Altima's Service Engine Soon (SES) light and reset it.<br /> <br /> <span style="font-weight: bold;">Obtain The Trouble Code</span><br /> <ol> <li>Turn the ignition key to the ON position and wait three seconds.</li> <li>Put the accelerator pedal to the floor and release it five times in less than five seconds.</li> <li>Wait exactly seven seconds. Put the accelerator pedal to the floor for ten seconds until the SES light flashes.</li> <li>Release the accelerator pedal and start counting flashes to obtain the four-digit trouble code.<br /></li></ol> <ul> <li>Long flashes (0.6 seconds) indicate the first digit of the code; count the blinks one through nine and write down the first digit. (Ten blinks indicates a zero.) </li> <li> The next three digits blink faster (0.3 second) and have a 1 second pause between digits.</li> <li>The ECM code repeats until you turn the ignition key to the OFF position.</li> <li>You can look up the trouble codes in the Service Manual.</li> <li>If you get four blinks of ten, or 0000, the ECM indicates no malfunction.<br /></li></ul> <br style="font-weight: bold;" /><span style="font-weight: bold;">Clear The Trouble Code</span><br /> <ol> <li> Clear the code and the SES light by holding the accelerator pedal down to the floor for 10 seconds or more while the SES light is blinking.</li> <li>When the pedal is released, the ECM will erase the trouble code(s).</li></ol>

on Feb 15, 2011 | 2002 Nissan Altima

1 Answer

See dealer now light flashing on 07 ram 2500 cummings


1. Turn the ignition switch to the ON position (Do not start engine).
2. Press and release the brake pedal two times.
3. Fully depress the accelerator pedal slowly two times within 10 seconds and hold it to the floor the second time.
4. Turn the ignition switch to the OFF/LOCK position and then let up on the accelerator pedal.

Make sure you're not letting up on the accelerator pedal before turning the ignition switch to the OFF/LOCK position.

Jul 20, 2014 | 2007 Dodge Ram Truck

1 Answer

How to unflood a 2001 4runner?


Push the accelerator pedal to the floor and hold it there while starting. Try for 10 seconds and wait for a while. Don't release the pedal.Repeat again while holding the pedal down all the time. The extra air should clear the fuel.

May 01, 2014 | 1997 Toyota 4Runner

1 Answer

1997 ford contour


hold pedal to floor and it tries to start ! Not sure if your vehicle has clear flood mode , Most vehicle have clear flood mode strategy programmed in the ECU , PCM ,ECM .when you hold the accelerator pedal to the floor the engine computer cuts down on the injector on time to clear a flooded engine .
Fuel pressure regulator problem ,maybe ! You say there was a blown fuel pump fuse an you replaced it ? Fuse's don't blow for no reason ? Fuel pump bad , short , too much current !
Disconnect the mass air flow sensor an see if it starts !

Apr 24, 2017 | Cars & Trucks

1 Answer

I have an issue with a 87 toyota pick up carburetor. Sometimes it doesnt want to start and sometimes it does a friend told me its that diaphram on the front of the carb with the 3 bolts but he could not...


Okay, your freind may be right, that part is called the accelerator pump, it is used for starting the truck, when you pump the gas to start it this pumps a few squirts of gas into the carb. what concerns me is that you hold the gas pedal to the floor to start it, most of the time an internal leaking carb floods the engine and holding the pedal down will let it start, a quick test would be to use a carb cleaner spray and before trying to start the truck hit the gas pedal and see if inside from the top of the carb look and see if you see a squirt of gas spray out, you will need some one to push the gas pedal or you can do it at the carb, if it squirts gas then the accelerator pump may be good and carb may be leaking and need rebuilding but if it doesnt squirt then its bad and then i want you to spray the carb cleaner into the carb and try to start the truck and if its due to the accel pump then after you spray into carb the truck should fire up and run without having to hold the pedal to the floor, if thats the case then replace accel pump if it still doesnt fire until you hold gas down then crab needs rebuilding . good day. hope this is helpful.

Apr 17, 2011 | 1987 Toyota Pickup

3 Answers

Reset check engine light after oil change


Turn the key to the on position. Not the start. And press the gas pedal all the way to the floor 3 times.

Feb 15, 2011 | Chevrolet Avalanche Cars & Trucks

1 Answer

Doesn,t want to start without holding the


poss injector dribble, leaking injectors fill pots over night does the engine spin over fast first try in the morning depressing the gas pedal to the floor make a NO FLOOD condition in the vehicle so it will not deliver any more fuel what do you think, possible?

May 15, 2010 | 1993 Mazda MX-6

2 Answers

Engine goes off when changing gears from P to D or


check engine light is on? if yes, You need an OBD scanner to dianose the problem. if no, its a mechanical problem. 1st, check if their is a vacuum leaks using the carburator cleaner to spray all over the emission, carburator, the vacuum lines if the idle going up you found the leak, now if still don't work, check if the fuel injector if not failing, check also the fuel filter and cracks on the exchaust manifold.

May 04, 2010 | 1999 Volkswagen Golf

1 Answer

Trouble starting must hold gas pedal to the floor


holding the gas pedal to the floor while cranking shuts off fuel flow to clear a flooded engine. Check for injectors staying open too long. Is check engine light on? If yes, get codes from free scan at Autozone.

Jan 10, 2010 | 2006 Ford Five Hundred

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...