Question about 1997 Nissan Quest

1 Answer

97 nissan quest gxe won't start, engien & rotor turns

97 nissan quest gxe won't start, engien & roter turns.I sprayed starting spray in intake air filter hose. Also, checked gast; it comes out of fuel line above fuel filter (pressure appears low).

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Nissan Master
  • 4,369 Answers

Pressure should be 40 psi. change pump in tank if bad.

go here for help

Posted on Jun 09, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I drove my 1998 nissan quest gxe in some deep water and it shut off, I changed the starter and it still won't start, help!!!!

You may have sucked water into the engine. Take the spark plugs out and try turning the engine over.

Apr 23, 2013 | Cars & Trucks

1 Answer

The van (98 Quest) starts good and runs well when HOT. There is no power when I step on the gas when cold it may make 5mph. I changed the plugs, wires, rotor, and cap. The codes read O2 sensor and...

IGNORE the knock sensor code, unless you have $600 to throw away for nothing. First step is to clean your MAF sensor with spray carb cleaner. Spray, do not touch the 1/2 inch long exposed wires inside the MAF sensor. The MAF is in the big plastic air intake tube near the air cleaner. 2 screws hold it on.

go to our site for step by step. we also know every issue with Villager Quest.


Jun 03, 2011 | 1998 Nissan Quest

1 Answer

Ran out of gas, now wont start

spray starting fluid into thrttle body & see if it starts then. If yes, replace fuel pump in tank.

Can you hear pump run for 5 seconds when you turn key on?

Dec 09, 2010 | 2000 Nissan Quest

1 Answer

Where is the map sensor located on a 99 nissan quest?

MAF sensor - on bigh air intake tube. clean with spray carb cleaner , do not touch heated wires, just spray.

Nov 14, 2010 | 1999 Nissan Quest

1 Answer

1996 nissan quest will not turn over it wants to start but wont does this mean the timing belt is broke?

Hello. Not necessarily. There are many possible causes of it not starting. Begin by changing the fuel filter. If that doesn't help, change the air filter. Finally try some starter fluid sprayed into the air intake when the cover is off of the air filter.

Sep 25, 2010 | 1996 Nissan Quest

1 Answer

Nissan Sentra AC rough idling

check the RPM booster switch which boosts up the RPM of car when AC is switched on.

Aug 01, 2010 | 1995 Nissan Sentra

2 Answers


First I would spray carburator cleaner into the intake(remove air filter) then if it don't start, check for spark. Reconnect your O2 sensor tho. That won't keep it from starting. Are you sure that you connected all the plug wires to the right plugs?

Feb 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

'95 nissan quest stalled at a stop. Will not start, only cranks

I worked on a '93 Quest last year. Couldn't find out why it wouldn't start. It was the distributor shaft not held onto its rotating gear. The roll pin had come out of the gear on the end of the distributor shaft. When the distributor cap was off, the rotor was turning with the shaft while the engine was cranking. So I thought that was okay. But when I put my finger on the rotor and it stopped turning, that is when I found out the problem. It's a stretch, but maybe the techs missed it. Take the cap off, and if you can spin the rotor either way just by hand, the distributor gear has come loose.

Looks like they really covered a lot. I suppose next they will you to replace the ecu. Good luck.

Oct 21, 2009 | 1995 Nissan Quest

2 Answers


hi the major problem is due to the single spade type connector going to a switch.. By means of a throttle pulley disconnected it and ur problem will be solved very simple... The switch must have gone bad...

thnk u!!!
rate me!!

May 01, 2009 | Honda CRX Cars & Trucks

Not finding what you are looking for?
1997 Nissan Quest Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides