Question about 2005 Nissan Quest

2 Answers

I need to change the brake light but can't figure out how to get the cover off and it is not in the manual. Do you know how to get to the bulb to change it?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

You have to pry the rear hatch trim top panel to access the back of the 3rd brake light

Posted on Aug 18, 2010

  • Level 1:

    An expert who has achieved level 1.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 15 Answers

Most 3rd brake light covers are held on with 2 plastic screws located on the sides, or the cover is just a push fit, easily pried off with a thin blade such as a putty knife screw drivers sceatch it up badly

Posted on Jun 04, 2010

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

GM Elec
  • 1000 Answers

SOURCE: change brake light bulb

I have not done one of these in a while, but I believe you open the tail gate and you will see two screws holding the lens in place. Remove the screws then the lens to access the bulbs.
Let me know.
Regards,

Posted on Apr 27, 2009

  • 1 Answer

SOURCE: How do I change the back brake light of a Hyundai Elantra?

If it is the light in the rear window, there are two plastic caps on either side on the base of the light. Pop off the cap and remove the screws inside. That should allow you to get to the bulb. I went to autozone for the bulb w/o removing it and they gave me the wrong one. If you have the bulb removed, you're better off, if not, the people at advanced got me the correct one without any issues. If it's the brake lights on the back of the trunk, you access those from inside the trunk. On either side, there are thumbscrews (sometimes under the fabric lining flaps). Once you remove the bulb carrier, you'll know which one is out. It usually lines up with the red cover but if you can borrow someone's time, have them look in your trunk at the bulbs as you test your parking lights to see which one lights and which one doesn't. Hope this helps.

Posted on Dec 26, 2008

  • 1 Answer

SOURCE: How do I change the brake light in my 2003 Chrysler T&C?

Once the liftgate is open, on the inside next to the tail light assembly, you'll see two black knobs. There are no screws involved, but you will need a regular screw driver and pliers. You need to gently pry or pull these two knobs outwards. Once these knobs are dislodged entirely, the assembly should easily come off. Brake bulb #3057 is the replacement. Good luck.

Posted on Feb 24, 2009

  • 1986 Answers

SOURCE: How to change a third brake light bulb for 1993 Toyota Camry?

open the trunk and look up along the top of the bumper and you should see two screws / nuts that secure the light assembly.

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was trying to change the inside trunk bulb , not the third brake lite! Put in a new buld it would not lite.


Did you find the fuse that the owners manual tells you is 4 the trunk lite?? If its not the fuse and the light it has 2 B the wiring somewhere. Check the bulb socket with a volt meter to make sure you have voltage at the socket itself with the trunk hood up obviously. It could also be the actuator switch. Good luck!!

Aug 30, 2014 | Cars & Trucks

1 Answer

Do not know how to bet the tail light sheild off so i can change the bulb


Hi,
I do not own the model you have, but generally, you access the tail light from the trunk (or the back door) of your car. Sometimes the taillight compartment is covered with a noise-absorbing material, which can be removed by un-buttoning.

Feb 24, 2013 | 2000 Plymouth Grand Voyager

1 Answer

Need to change rear brake light bulb on a 2000_L sedan. Owners manual addresses only the turn signal bulb change proceedure. The brake light fixture is flat not round.


there is an access cover in the trunk.Open that and just pull the bulb fixture out replace the bulb and place back in the hole.

Apr 07, 2012 | Saturn Cars & Trucks

2 Answers

I just purchased a 1996 cavalier. It didn't have an owners manual and i need to know what the abrieviations on the fuse box stand for. I'm trying to find the fuse for the brake lights and rear turn...


Hi, the likely problem is the turn signal switch. The signals and brake lights use different fuses. You can get an owners manual here:
http://www.extendedgmwarranty.com/owners-manual/chevrolet/1996-Chevrolet-Cavalier.pdf

A new switch is about $40, and it isn't too hard to replace. Make sure you get one that has the same controls as yours does. To replace the switch, remove the covers from the steering column, disconnect the switch and unscrew it from the column.

Please let me know if you have questions, and thanks for using FixYa.

jturcotte_2105.gif

Aug 18, 2011 | 1996 Chevrolet Cavalier

1 Answer

How do you change the brake light on chevrolet caprice 1992


Hello Friend:

To change your brake light on your Car is Done from inside your Trunk, You'll need to open trunk, and on either side there is a cover on the left and right side,That will be removeable.

Just remove the cover with your Hands and it will expose your Wiring to your bulbs and you'll see a metel socket that holds your Light Bulbs, Just turn or Pull that socket out that the Wiring goes to.

Now you can remove your bad bulb and replace it with a new one.

on a Caprice you'll have 2-3 Bulbs in the Lighting assembly just have someone Push down the Brake Pedal. So you can see the Light thats not Working.

This will get your Brake Light Working. Since its only 1- Bulb thats out Eliminates that you have a Bad Brake Light Switch. If both sides are out it could be your brake light swith.

Sir I'm sure this will solve your problem,I thank you for Using FixYa
Please let me know if you solved your Problem by Voting .

Thanks Again From: d_hubbs

Aug 21, 2010 | 1992 Chevrolet Caprice

2 Answers

How do I change the rear brakelight?


I'm guessing that in your market the brake lights are actually in the body (as opposed to in the bumper bar where they are in Australia). If this is the case, then open the back tail gate and you will see 2 screws or bolts that are normally covered by the closed tail gate. Remove these 2 bolts and then grab the outer vertical edge of the lamp assembly and pull rearwards. Getting your fingers partially under the edge will help, but it will be hard on your finger tips. I could recommend using a screwdriver, but you would run the risk of scratching the paintwork. Once the lamp is out, twist the relevant globe holder 45 degrees and then change the globe. Of course, if your brake light is in the bumper bar, you will only need a phillips-syle screwdriver.

Oct 16, 2009 | 2001 Suzuki Xl 7

1 Answer

How do you get to the brake light in a 2004 Maxima?


you have to go in the trunk and move the cloth covering away from the light casing, then twist the bulb out

Jun 16, 2009 | 2005 Nissan Altima

1 Answer

High Level Brake bulb replacement


If memory serves, there are two screws holding this light assy to the rear package deck. They are covered (LH and RH side of this assy). remove the covers and using a phillips screwdriver, remove the screws and lift the assy up and away from the rear glass. you now have access to the bulb and socket.

May 18, 2009 | Hyundai Motor 2004 Accent

4 Answers

Fuse for brake light on 2007 Jeep Liberty


I dont have owners manuel and need to know what fuse is my brake lights ? All brakes lights are out . Thank you

May 03, 2009 | 2007 Jeep Liberty Sport

2 Answers

How do I change the brake light in my 2003 Chrysler T&C?


Once the liftgate is open, on the inside next to the tail light assembly, you'll see two black knobs. There are no screws involved, but you will need a regular screw driver and pliers. You need to gently pry or pull these two knobs outwards. Once these knobs are dislodged entirely, the assembly should easily come off. Brake bulb #3057 is the replacement. Good luck.

Feb 17, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
2005 Nissan Quest Logo

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...