Question about 2002 Ford Explorer
Unhook the battery and let it sit for about a half hour. This should reset the ecm.
Posted on May 31, 2010
If ur resetting a check engine light problem or clearing codes from computer than go to an auto store most will scan for free and can clear codes for u some stores such as autozone /advanced auto do this service for free check ur local area ---if u want to clear computer by disconnecting battery then enter code for radio so u dont get locked out when u reconnect battery
Posted on May 31, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2002 Ford Exlorer XLT
That year Explorer was notorius for rear ABS sensors going bad. If your ABS light is on as well this may be your problem. Also they were notorious for 4WD modules going bad. This problem is more expensive. I would advise you to have it checked on a computer to see what codes you have.
Posted on Apr 14, 2009
you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful
Posted on Aug 15, 2009
Check in your Owners Manual or download this document from this link: Ford/maintenance/owners_manuals
Hope helps (remember to rate this answer).
Posted on Apr 11, 2011
Testimonial: "yes thank you, i went to the web site ford gave me and didnt help at all. this was very useful since i didnt get a manual with my truck. "
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
Tips for a great answer:
Apr 02, 2016 | 2002 Ford Explorer
Jan 08, 2016 | Cars & Trucks
Oct 19, 2015 | 2002 Ford Explorer
Sep 23, 2011 | 2002 Ford Explorer
Feb 02, 2010 | 2002 Ford Explorer
Jan 16, 2010 | 2002 Ford Explorer
Jun 05, 2009 | 2002 Ford Explorer
Apr 05, 2009 | 2002 Ford Explorer
Mar 19, 2009 | 2002 Ford Explorer
Jan 30, 2009 | 2002 Ford Explorer
1,803 people viewed this question
Usually answered in minutes!