Question about 2002 Chevrolet Monte Carlo

1 Answer

Wiper blades on the off position are straight up and down have to leave on delay to avoid this ...i was told theres a transmission for the wipers they is stripped how do i fix this myself

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Hello, the problem is not with the wiper transmission, the problem is the park tab on the wiper motor mounting bracket is bent or broken. you will need to replace the wiper motor mounting bracket

Posted on Jun 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 HYUNDAI ACCENT, problem is the Windshield Wiper operation is malfunctioning, in the Delay mode, and in the off position, Windshield Wiper arms/blades stop at the half point on the Windshield glas


The park position is controlled inside the motor/actuator assembly. Not sure if it can be repaired. See if it is assembled with screws versus rivets. A new assembly is less than $100.

Jul 05, 2017 | 2000 Hyundai Accent

1 Answer

Wipers don't touch windshield


The wiper arm springs are weak,just grab a used set of arms as most ventures wipe great.People who stick their wipers straight up,usually when freezing rain is coming ,ruin their wiper arm springs and have less wiping pressure too, so have to replace their arms at some point. PEOPLE STOP LEAVING YOUR ARMS IN THE UP IN THE AIR,OFF THE GLASS POSITION.

Mar 10, 2017 | 2001 Chevrolet Venture

2 Answers

Windshield shutters while in delayed mode, it


Excessive grease in wiper motor. Motor needs to be removed and the grease cleaned out. Regrease only the areas needing to be greased.

There is also a recall for this vehicle for the wiper module. Call the dealer with your vin # to see if it has been done. I will post the instructions for motor removal and install.

1. Turn the key to the OFF position.
2. Open the hood.
3. Remove the three push-in retainers that attach the air inlet grille (leaf screen) to the plenum sheet metal.
4 . Lower the hood to the secondary latch.
5. Using a suitable marker or masking tape, mark the location on both wiper blades on the windshield.
6. Remove the covers from the nuts that attach the wiper arms.
7. Remove the nuts from the wiper arms.
Important
If the rocking action in the next step fails to loosen the wiper arm, it may be necessary to use a standard top-post battery cable terminal puller to remove the wiper arm.
8. Rock the wiper arms back and forth to loosen and remove them from the wiper transmission shaft.
9. Remove the antenna mast.
10. Remove the 10 mm hex head nut that attaches the left and right ends of the air inlet grille to the plenum sheet metal.
11. Remove the air inlet grille and reposition it up to the windshield. It is not necessary to disconnect the washer hose.
12. Remove the two 10 mm hex head bolts that attach the wiper module to the plenum sheet metal.
13. Disconnect the electrical connector.
14. Position the new wiper module to the vehicle and connect the electrical connector.
15. Install the wiper module in the plenum sheet metal.
16. Install the two 10 mm hex head bolts that attach the module to the plenum sheet metal. Tighten nuts to 30 N·m (22 lb ft).
17.Turn the ignition switch to the ON position, turn the wiper switch ON, and visually verify that the wiper transmissions operate. After visually verifying operation, turn the wiper switch to the OFF position and allow the wiper transmissions to stop moving before turning the ignition switch to the OFF position. The wiper motor will now be in the PARK position.
18. Using the marks or masking tape that were placed on the windshield, align and position the wiper arms on the wiper transmission shafts.
19. Install the nuts on the wiper transmission shafts. Tighten the nuts to 30 N·m (22 lb ft).
20. Install the covers on the wiper arm nuts.
21. Remove the marks or masking tape from the windshield.
22. Open the hood.
23. Install the three push-in retainers that attach the air inlet grille to the plenum sheet metal.
24. Close the hood.
25. Verify that all functions of the wiper system (low, high, delay, etc.) operate properly.

Apr 02, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

I cant figure out how to change my windshield wiper blades on 2001 ford ranger


How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 16, 2009 | 2001 Ford Ranger Regular Cab

2 Answers

How do I remove front wiper blades to replace with new ones on my 2006 nissan quest


How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 14, 2009 | 2006 Nissan Quest

1 Answer

Where is the windshield washer relay located


They (the wiper motor and mechanism) are underneath the cowl vent screen.

To replace the motor and mechanism:
1: Turn the ignition to the on position with the wipers at low speed. When the arms are point straight up, turn it off.

2: Use a small screwdriver and pry the plastic caps from the wiper arm mounting ends.

3: Disconnect negative battery terminal

4: Remove the small retaining nup from each wiper arm, then the arms.

5: Remove the cowl screen by turning the eight plastic retainers 1/4 turn counterclockwise. Next remove the six screen retaining clips. If it's a 2000 or later, remove four bolts that secure the arm monting bar so that you can access the wiper motor.

6: Disconnect the electical connections and remove the four screws that secure the motor and mechanism to the cowl, and take out the motor-mechanism assembly.

7: The drive mechanism isn't serviceable, but the motor can be replaced. Remove the operating arm nut from the motor shaft, and remove the three screws that hold the motor to the drive mechanism.

8: Reinstall the wiper mechanism into the cowl and connect the electrical connectors. (Before reinstalling the wiper arms and blades, turn the ignition to the on position and turn the wiper switch to either LO or HI, then turn the wiper switch Off. This lets the motor cycle to the park position thus avoiding damage to the arms and drive mechanism).

9: Install the wiper pivot arms, ensuring the blade tips align with the park reference mark at the base of the windshield.

10: Ensure that your wiper blade is fully seated on the wiper arm before operation the wipers.

11: Finish up the reverse way you began.

Jun 24, 2009 | 1999 Ford Taurus

1 Answer

Wipers willnot return to park position


I've fixed this problem before. You have to disconnect the wiper transmission from the wiper motor. Put wipers in off position, unbolt the plate on top of wiper, turn wipers on then off. In the off position see where the wiper transmission is position in relation to where the park position is, remove the top plate from wiper motor and position it so as to be able to reconnect the wiper transmission now in the proper place. Please keep me informed. thanks you

Jun 03, 2009 | 2002 Chevrolet Impala

2 Answers

F250 removing windshield wipers from truck how do I do this


lift the wipers to their "up" position. at the base you will see a small clip, lift up on this clip and let the wiper down slowly while holding out the clip. the wiper will not go all the way down, in this position pull up on the base and the wiper should come free.

Feb 23, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

03 Taurus wiper problem


What I would suggest you do is the following:

1) Remove the driver side wiper (arm & blade).
2) Start the car and turn on the wipers.
3) When the passenger wiper is straight up and down .. turn off the car. This leaves the wiper in position.
4) Re-install the drivers side wiper and put it back on so its position is the same as the passenger - making them parallel

Start the car and test

Feb 23, 2009 | 2003 Ford Taurus

2 Answers

Wind shield wiper


Check to see if the stud that they sit on is not spinning . Make shure that they are tight. Start by parking your wipers. then loosten the wipers and put them back on where they should be parked and tighten them up this should fix the problem . If not you may need to buy new motor unfortunatel. I hope this helps. Don't forget to rate my answer. thanks.

Feb 11, 2009 | 2000 Buick Regal

Not finding what you are looking for?
2002 Chevrolet Monte Carlo Logo

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...