Question about 2004 Chevrolet Blazer

1 Answer

What size nut goes on the stater plate on the ac compressor?My stater plate came off, and I replace it, but the reason it came off in the first place is that the nut that holds it tight came off. Do you know what size nut I need to replace it? I don't want to get the wrong size and strip the bolt.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

My best suggestion....SALVAGE YARD.

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 chevy venture what size is belt that bypasses a.c. compressor the exact measurements


There is no belt to bypass the AC cataloged, when the AC is not ordered on the car (AC delete) or the compressor is removed for some reason then you must use what is called an AC delete pulley, it bolts in place of the AC compressor and you use the same belt. The pulley is cheap and either the dealer or most good auto parts stores like NAPA (or others) can order it for you, in the aftermarket the pulley's are made by a company called DORMAN

Jan 05, 2017 | Cars & Trucks

1 Answer

How many fasteners are on ac compressor clutch plate 02 volvo s60


clutch not like car clutch basically single exterior nut then start pulling outer assembly pulley and electrical components apart need some special tools and a rebuild kit to repair an auto a/c compressor

Aug 01, 2016 | Volvo Cars & Trucks

1 Answer

How do I replace a tension pulley on Toyota tocoma pick up


Before replacing anything be sure of the problem. A siezed AC compressor or damaged crank pulley could also be the cause. If it is the tensioner pulley, remove the 14mm nut on the front of the pulley and it comes right off. The new part should come with a new plate that goes behind the nut. You can re-use the stud that the adjusting bolt threads into if it is not damaged. If your motor is a 5VZ, be sure to not over-tighten the drive belts or it could develop a rod knock.

Feb 23, 2015 | 2004 Toyota Tacoma

1 Answer

How to replace the ac compressor clutch on a 2000 gmc yukon xl?


the clutch removal is easy, remove the nut on the front and remove the pressure plate, then remove the retaining clip around the bearing support and pull off the clutch,
it is hard to find a new cllutch, most companies just want to sell you a new compressor. if you need a new one, check http://www.rockauto.com/ first, then search amazon and ebay for the part number at rock auto, sometimes you can find one less expensive than rock auto but overall rock has the best deals
I can get you 5% off if you decide to get one there, just ask

Aug 15, 2014 | 2000 GMC Yukon XL

1 Answer

Ford focus front strut replacement


basically remove the wheel ( after placing the vehicle on jack stands). remove the bottom ball joint connection ( bolts or ball joint with a ball joint splitter) use 2 spring compressors and close up the spring mark one bolt in the engine bay at the top of the strut so you know where the unit goes on reassembly The bolts control the wheel alignment)undo the bolts and drop the unit out the bottom. undo the nut at the top and release the spring clamps. Lift the spring and top plate of the shaft. Undo the insert nut and remove out of the tube. Insert new insert and reverse the procedure. A workshop manual ( genuine or after market will have the procedure in full with photos)

Jul 25, 2014 | 2000 Ford Focus

1 Answer

I have a 2006 Ford Taurus. Yesterday the serpentine belt broke and I replaced it. My car was looked at by two men who know a good deal about cars. They both said the reason the belt broke was because...


AC PULLEY AND BEARING CAN BE REPLACED.YOU WILL NEED AC COMPRESSOR TOOLS LIKE SEAL TOOL AND PULLEY BEARING TOOL THE AIR CONDITIONER SYSTEM HAS TO BE DISCHARGED TO FIX AC COMPRESSOR PULLEY AND BEARING. YOUR AC COMPRESSOR PULLEY HAS A NUT AND SNAP RING HOLD IT IN PLACE.GO TO DEALERSHIP TO SEE IF THEY HAVE THE AC PULLEY NUT AND SNAP RING.SOME TIME YOU WILL HAVE TO BUY A NEW AC PULLEY BEARING AND SEAL TO GET A NEW NUT AND SNAP RING.AUTO ZONE HAS AC TOOL YOU CAN RENT TO FIX AC BUT YOU HAVE TO TAKE CAR TO DEALERSHIP AND GET AC SYSTEM DISCHARGED FIRST BEFORE YOU CAN WORK ON AC COMPRESSOR.

Dec 01, 2010 | Ford Taurus Cars & Trucks

1 Answer

How do i tighten a/c belt,i lost one and the new one is very loos


there should be a single pulley in-between the a/c compressor and crank shaft it is a little higher than a/c compressor and has a 15mm socket sized nut on the front. loosen the nut and behind the pulley should be a long 10mm head sized bolt to tighten and loosen the pulley with.

May 25, 2009 | 1997 Plymouth Voyager

2 Answers

Need to bypass ac compressor on a1997 chevy lumina 3.1l


the models without AC use a AC delete pulley, so there is only one belt size, the pulley goes where the compressor is in your with AC car, contact Ford for the AC delete pulley

Apr 28, 2009 | 1998 Mercury Mystique

1 Answer

1998 Volvo V70 A/C Intermittent


I had exactly the same problem. When your engine is cold and off check the gap on your ac compressor with a feeler gauge, it should be between 0.3 and 0.5mm. If it is larger you need to re-shim which invloves undoing a nut on the end off the compressor and removing the clutch plate, then removing the appropriate shims (look like washers) then replace. The reason it blows warm after 10 minutes or so is because the ac compressor gets hot and the clutch gap gets too large for the electro-magnetic clutch to engage. Some people would say that you need a new compressor but all you need to do is a re-shim.

Mar 01, 2009 | 1999 Volvo V70

1 Answer

Can I bypass ac compressor


You can go to an auto parts dealer.They sell a bracket with a pulley that takes the place of an a/c compressor and allows you to use the same size belt It's available at a place like NAPA or Autozone.

Feb 25, 2009 | 2002 Ford Windstar Cargo

Not finding what you are looking for?
2004 Chevrolet Blazer Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...