Question about 1995 Ford F150 Styleside Regular Cab

1 Answer

How to remove bearings from brake rotor 95 f150 5.0 2wl dr

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

The way I've always done is thread the spindle nut on the spindle with the rotor off. If you push the rotor back on the nut will push the outer bearing out. Tilt the rotor back and pull it off quickly and it should remove the inner bearing and seal.

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 83 Bronco 351w I am doing the brakes and the passenger side rotor needs to be replaced can someone walk me through this thanks


Personally I would replace both rotors to prevent a future brake imbalance.

* chock rear wheels, raise front of vehicle and place on stands.

* remove wheels, remove brake calliper and bracket assemblies.

* remove bearing hubs from axles, via removal of bearing adjustment nut

*remove hub seals, clean and inspect bearings, repack with HT bearing grease.

* the brake rotor bolts to the rear of the hub, you will have to remove and replace rotor to hubs, make sure all bolts are thread locked with loctite 263 and tensioned to spec.

* pack hub with grease, install seals, fitt hub assembly and adjust wheel bearing preload, install new split pins.

* fitt brake calliper and brackets, fit new brake pads,

* fitt wheels lower vehicle, test brake for function

Hope this helps..

Aug 02, 2016 | Cars & Trucks

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

I am getting a pulsing feeling from the front wheels when braking on my 2004 Chrysler Sebring. It feels like one or more of the rotors are warped. How do I replace the front rotors with new ones. Thanks.


If they are not worn beyond tollerance they can be machined on the vehicle.
Also make sure its not tyres or wheel bearings.

remove wheel
remove brake caliper( leave the hose connected)
remove centre cap
remove split pin and lock
unscrew bearing hub nut
rotor should come off
fit new bearing races in new rotor
grease new bearings
fit inside bearing and seal
refit rotor, outer bearing,washer,nut,lock, splitpin and centre cap
(tighten nut until no play in bearing plus 1\8 of a turn)
refit caliper and wheel
bleed and test brakes before driving

Apr 28, 2010 | 2004 Chrysler Sebring

1 Answer

Replace front wheel bearing. How? 95 Oldsmobile Cutlass ciera


remove front tire ,brake caliper ,rotor and axle nut its gona be a hub bearing it has 3 bolts holding it

Apr 02, 2010 | 1995 Oldsmobile Cutlass Ciera

2 Answers

Grease leaking from the front passenger


Inner, (Large), wheel bearing has failed. This has caused the grease seal to fail.
Solution is to replace the bearing, and seal.

1.Check the bearing race in the brake rotor. If any pits, scoring, or other evidence of break down is present, the bearing race must be replaced also.

2.Check the outer wheel bearing and bearing race also. The inner bearing receives the most wear, but cleaning, and inspection of both bearings, and races is a standard procedure.

3.Observe the area on the spindle where the grease seal contacts. Insure that the spindle area is of good repair, and no scoring is evident.

The Black residue that you observe is grease mixed with brake dust.

The vehicle must be jacked up in the front, with safety stands placed in the proper area on both sides. Wheel chocks should be used behind the rear tires. The vehicle should be on a flat hard surface.

The wheel/tire is removed, then the brake caliper. The caliper is not removed from the brake hose, but hung from a hanger device, from the frame of the vehicle. (Small rubber tie down strap? Wire clothes hanger?)

Then the dust cap is removed, cotter pin, and spindle nut. Ease the brake rotor out, be ready to catch the outer bearing. Remove the brake rotor.

Rotor laying on two small wood blocks, (2x4's? 4x4?), blocks under rotor face. (Where the brake pads rub against)
Blocks placed so area of grease seal is not resting on them. Rotor is laying on blocks with outside of rotor facing up. (Outside of rotor faces outside of Tahoe)

Take a long punch, and tap out the grease seal from the inside of the rotor. Through the hole where the spindle goes through. Be careful that the punch is resting on the metal ring of the seal, and not the bearing race edge.


Oct 11, 2009 | 1998 Chevrolet Tahoe

1 Answer

Front brakes


Hi there;
To replace the front rotors on your truck you will need to remove the hub & bearings, yes, how-ever you should not have to replace the bearings. If you take it a-part & find there is metal filings inside, then you would want to. But if the grease is only dirty you should just clean off all the old grease & repack your bearings.

Word of caution: If you are not familiar with repacking & adjusting wheel bearings you may want to consult a local gaurage for a demonstration as if you do not do it properly you can cause a lot of damage to you & your truck.

Having said that, once you get the hub off you will see that the rotor is bolted to the hub. remove the bolts, install the new rotors & install & torque the bolts.
Hope this helps
Farrout!

Mar 17, 2009 | 1995 Toyota 4Runner

1 Answer

RELACING WHEEL BEARINGS IN A 95 JEEP GRAND


Front wheel bearings can be done at home rear wheel bearings will require a hydraulic press and an axle puller. Either job can be difficult depending on amount of rust and availability of tools. The front wheel bearings are an assembly and once the jeep is up on jack stands, with the tires, brake calipers, and rotors removed, it is only a matter of removing the axle nut and 3 bolts (which can be difficult depending on rust) holding in the old bearing assembly

Feb 22, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

3 Answers

Rotors


See Figures 1, 2 and 3
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in .
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the two 6mm screws from the brake disc.
0900c1528005fbe4.jpgFig. 1: Remove the two 6mm screws securing the brake disc
  1. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  2. Remove the caliper bracket.
0900c1528005fbe5.jpgFig. 2: Remove the bolt and guide pin from the caliper bracket, then remove the bracket
  1. Remove the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly and alternately to prevent cocking the rotor.
0900c1528005fbe6.jpgFig. 3: Remove the brake disc from the caliper assembly
  1. Installation is the reverse of the removal procedure.
  2. If equipped, enable the SRS system and connect the negative battery cable.5f83e91.jpg810cd9d.jpg14f1553.jpgFig. 1: Remove the two 6mm screws securing the brake Fig. 2: Remove the bolt and guide pin from the caliper
  3. Fig. 3: Remove the brake disc from the caliper assembly
Good luck...........

Oct 24, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1995 Ford F150 Styleside Regular Cab Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...