Question about 2000 Ford Expedition

1 Answer

Check eng light on low egr flow replace the egr valve and senore check eng light now says evap and low egr flow?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 749 Answers

A very common issue that can cause this code is the EGR valve but most commonly the DPFE Sensor differential pressure feedback egr. For the evap code would make sure no lines may have been disconnected while replacing the egr valve. It is possible the the evap code may be a separate issue.

Posted on May 31, 2010

  • howedyone May 31, 2010

    replace EGr valve and the DPFE Sensor already still showing code for low flow on EGR?

  • Jonathan S
    Jonathan S May 31, 2010

    When replacing the dpfe sensor.Were the hoses replaced quite often these become plugged with carbon. Some kits come with replacement hoses while other don't.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does fault code P0497 mean for Honda Cr-v ?


Nothing for that code either. Are you sure you are reading the reader properly?

P1382 Cylinder Position Sensor No Signal P1456 EVAP Emission Control System Leak Detected (Fuel Tank System) P1457 EVAP Emission Control System Leak Detected (Control Canister System) P1459 EVAP Emission Purge Flow Switch Malfunction P1486 Thermostat Range/Performance Problem P1491 EGR Valve Lift Insufficient Detected P1498 EGR Valve Lift Sensor High Voltage P1508 IAC Valve Circuit Failure

Dec 30, 2015 | Honda Cars & Trucks

1 Answer

Code po496 how can i fix it


code p0496 refers to evaporative emission system--high purge flow===causes--wiring--EVAP valve--mechanical fault
check that the cap is on correctly
replace EVAP valve

Apr 09, 2015 | Cars & Trucks

1 Answer

I'm receiving an Error code po441, I took it to the dealer who replaced the EGR valve and reset the engine light and cleared codes a week ago, now my engine light just came back on with same code


Some dealer you got there

PO441-EVAP System --Incorrect Purge Flow

They may have found an EGR Valve issue,
but they certainly blew off the EVAP Code

I would guess you have a bad EVAP Canister
Purge Valve or some other purge control
item

Feb 15, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

I have no gears forward or reverse. My Vehicle is a 2003 Dodge Ram 1500 4x4 Hemi with 170,000 on the clock. Fluid is clean and full with no leaks. I have the following trouble codes:...


Your scanner will give you the code but it will not tell you how to fix your vehicle. Scanners basically tell you what systems to check or what systems are failing.

These are what your codes mean:

P0700: Transmission Control Module
- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module. This is just a informative code.

P0734: Gear ratio error in 4th gear
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0732: Gear ratio error in 2nd gear
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0731: Gear ratio error in 1st gear
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0871: Transmission Fluid Pressure Sensor Switch C

P0876: Transmission Fluid Pressure Sensor Switch D

Emissions Codes:

P0400: Exhaust Gas Recirculation Flow Malfunction
- Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control valve stuck closed
- EGR volume control solenoid valve
- Dead (Weak) battery
- EGR temperature sensor and circuit
- EGR Valve

How to fix :
- Clean EGR Valve
- Repair EGR harness or connector
- Replaced EGR volume control solenoid valve
- Replaced EGR volume control valve

P0440: EVAP Emission Control System Malfunction
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve

How to fix:
- Retight or replaced fuel tank filler cap
- Replaced damage or leaking EVAP canister

P0456: EVAP Control System Leak Detected (Very Small Leak)
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve

How to fix:
- Retight or replaced fuel tank filler cap
- Replaced damage or leaking EVAP canister

P0441: EVAP Emission Control System Incorrect Purge
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve

How to fix:
- Retight or replaced fuel tank filler cap
- Replaced damage or leaking EVAP canister

Based on the info check your EVAP system. I would check for leaks and maybe replace the EGR and the canister.

For the transmission check the TCM also you may need to take it to a mechanic though.

Hope this helps a little.

- Tech 101 (ASE CERTIFIED MASTER TECHNICIAN)
- Larson's Mobile Auto Repair
- 209-845-7620
- Oakdale, CA

Dec 31, 2010 | Dodge Pickup Cars & Trucks

2 Answers

Codes P0401 and P0441 on a 1996 98 Olds


P0401--- the egr valve has insufficient air flow. Needs to be taken off and cleaned, if not replaced. The port holes might be clogged up, or the valve itself might be bad.
P0441---- The evaporative emission control purge valve has low air flow, probably do to the egr valve.
If you take off the egr valve, you will need to replace the gasket, or it won't seal right when it's put back on.

May 05, 2010 | 1996 Oldsmobile Ninety Eight

1 Answer

Check engine light low air flow


I assume you mean EGR low flow P0401. This is ging to be a faulty EGR dpfe sensor or the ports i nthe intake are clogged behind the EGR valve.

Mar 16, 2010 | Ford F-150 Cars & Trucks

1 Answer

P0401 egr flow all senors,ports working properly at shop with ase


check ur egr valve -there are 3 parts to the egr --the dpfe[differential pressure feedback egr ]sensor//egr valve//actuator solenoid--++biggest problem with the egr valve is that it gets carboned up and the valve is stuck remove and clean the valve and tube with a carb cleaner and check valve for movement if faulty replace also check vacuum line and vacuum to egr unit

Feb 14, 2010 | 2001 Mitsubishi Eclipse

1 Answer

99 5.4 Expedition issues


P0401 - EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
  • Vacuum supply
  • EGR valve stuck closed
  • EGR valve leaks vacuum
  • EGR flow path restricted
  • EGRVR circuit shorted to PWR
  • VREF open to DPF EGR sensor
  • DPF EGR sensor downstream hose off or plugged
  • EGRVR circuit open to PCM
  • VPWR open to EGRVR solenoid
  • DPF EGR sensor hoses both off
  • DPF EGR sensor hoses reversed
  • Damaged EGR orifice tube
  • Damaged EGRVR solenoid
  • Damaged PCM

P1299 - Cylinder Head Over Temperature Protection Active Indicates an engine overheat condition was detected by the cylinder head temperature (CHT) sensor. An FMEM Strategy called Fail-safe Cooling was activated to cool the engine.
  • Engine cooling system concerns
  • Low engine coolant level
  • Base engine concerns

P0300 - Random Misfire The random misfire DTC indicates multiple cylinders are misfiring or the PCM cannot identify which cylinder is misfiring.
  • Camshaft position sensor (CMP)
  • Low fuel: less than 1/8 tank
  • Stuck open EGR valve

P0443 - EVAP Control System Canister Purge Valve Circuit Malfunction The PCM monitors the EVAP canister purge valve circuit for an electrical failure. The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified purge duty cycle by PCM command.
  • VPWR circuit open
  • EVAP canister purge valve circuit shorted to GND
  • Damaged EVAP canister purge valve
  • EVAP canister purge valve circuit open
  • EVAP canister purge valve circuit shorted to VPWR
  • Damaged PCM

P1451 - EVAP Control System Canister Vent Solenoid Circuit Malfunction Monitors the canister vent (CV) solenoid circuit for an electrical failure. The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
  • VPWR circuit open
  • CV solenoid circuit shorted to PWR GND or CHASSIS GND
  • Damaged CV solenoid
  • CV solenoid circuit open
  • CV solenoid circuit shorted to VPWR
  • Damaged PCM

P1309 - Misfire Monitor Disabled When the misfire monitor is disabled, usually due to the input signal generated by the camshaft position (CMP) sensor, by sensing the passage of teeth from the CMP wheel.
  • Camshaft position sensor
  • Powertrain control module
  • ECT, MAF, and CKP sensors

with the codes you have here I would look in the direction of the egr valve first because that will cause the bucking and stalling, and the misfires, but so will the canister vent solonoid. the misfire codes and the cylinder overtemp code could be from overheating or because if the misfires.

Jul 27, 2009 | 1999 Ford Expedition

1 Answer

1995 mercury villager check engine code p1200 injector open


P0400 = EGR Flow
P0325 = knock sensor (Do not ever change a knock sensor, they don't affect anything and cost $600 to replace for absolutely no gain)
P1200 = I can't find this one. I think it's injector flow
report back on what you find.
Egr flow may be plugged egr passages or a bad solenoid.
--------------
1996 PCED OBDII-Villager SECTION 1B: Description and Operation
Exhaust Gas Recirculation System
Exhaust Gas Recirculation (EGR) System Operation The exhaust gas recirculation (EGR) system (Figure 1 below) recirculates a portion of the exhaust gases into the intake manifold under average vehicle driving conditions to reduce combustion temperatures and exhaust gas NOx content. The amount of exhaust gas recirculated varies according to operating conditions and will be cut completely under:
  • Engine starting condition
  • Low engine coolant temperature condition
  • Excessively high engine coolant temperature condition
  • Engine idling condition
  • High engine speed condition
  • Mass air flow sensor failure
The exhaust gas recirculation (EGR) system on the Villager uses the exhaust gas recirculation/evaporative emission (EGR/EVAP) control solenoid valve to provide vacuum to both the EGR valve and the EVAP canister when commanded by the PCM. If the exhaust backpressure is sufficient to close the EGR backpressure transducer valve, vacuum is sent to the EGR valve and allows EGR gas to flow into the intake manifold. If the exhaust backpressure is not sufficient, the EGR backpressure transducer will remain open and allow vacuum from the EGR/EVAP control solenoid to vent to the atmosphere.
The EGR system monitor, for OBD II regulations, uses an EGR temperature sensor to monitor the EGR system. The EGR temperature sensor is a thermister located in the EGR passageway. When hot exhaust gas is recirculated into the engine, the temperature at the EGR passageway increases. This increase is sensed by the EGR temperature sensor and a signal is sent to the PCM to indicate EGR flow. If the EGR temperature sensor does not detect EGR flow when commanded by the PCM after two consecutive drive cycles, the malfunction indicator lamp (MIL) will be illuminated and a diagnostic trouble code (DTC) will be stored. The MIL will be turned off after three consecutive drive cycles are completed with no malfunctions detected. The DTC will remain stored in the PCM memory until 80 drive cycles have been completed without the same malfunction detected in the system.
Figure 1: Exhaust Gas Recirculation (EGR) System Diagram Item Number Description 1 — EGR/EVAP Control Solenoid 2 — Air Cleaner Housing 3 — Throttle Valve 4 — EGR Temperature Sensor 5 — EGR Valve 6 — EGR Backpressure Transducer 7 — EVAP Canister
Exhaust Gas Recirculation (EGR) Backpressure Transducer Valve The exhaust gas recirculation (EGR) backpressure transducer valve is used to control EGR. The EGR valve is operated by ported vacuum, but the ported vacuum will normally be vented off at the EGR backpressure transducer valve. As rpm increases, exhaust pressure increases and pushes on the diaphragm in the EGR backpressure transducer valve and closes the vacuum vent.
Figure 2: EGR Backpressure Transducer Value
Item Number Description 1 — Throttle Valve 2 — Vacuum Port 3 9D475 EGR Valve 4 9F452 EGR Backpressure Transducer Valve 5 — EVAP Canister 6 — EGR/EVAP Control Solenoid 7 — Vent
EGR/EVAP Control Solenoid The exhaust gas recirculation/evaporative emission (EGR/EVAP) control solenoid (Figure 3) is controlled by the powertrain control module (PCM). The EGR/EVAP control solenoid controls vacuum to both the exhaust gas recirculation (EGR) valve and to the evaporative (EVAP) emission canister. When the EGR/EVAP control solenoid is off (12 V signal from the PCM) vacuum is supplied to both the EGR valve and to the EVAP canister. When the EGR/EVAP control solenoid is on (ground supplied by PCM) vacuum is vented to the atmosphere keeping the EGR valve closed and no vacuum to the EVAP canister. The PCM will command the EGR/EVAP control solenoid on at:
  • Engine starting condition
  • Low engine coolant temperature condition
  • Excessively high engine coolant temperature condition
  • Engine idling condition
  • High engine speed condition
  • Mass air flow sensor failure
Figure 3: Exhaust Gas Recirculation/Evaporative Emission (EGR/EVAP) Control Solenoid
Exhaust Gas Recirculation (EGR) Temperature Sensor
The exhaust gas recirculation (EGR) temperature sensor (Figure 4) is a thermister type sensor that monitors the temperature of the exhaust in the EGR passageway. As the EGR flow increases, the temperature increases. This process creates a change in the resistance of the sensor, which decreases as the temperature increases. The signal is sent to the powertrain control module (PCM) to indicate that the EGR system is working properly. If the EGR temperature sensor does not change resistance as the PCM expects on two consecutive drives, the malfunction indicator lamp (MIL) will be illuminated and a diagnostic trouble code (DTC) will be stored.
Figure 4: EGR Temperature Sensor Exhaust Gas Recirculation (EGR) Valve
The exhaust gas recirculation (EGR) valve (Figure 5) recirculates portions of the exhaust gas back into the intake manifold to reduce the amount of the NOx released during combustion and to reduce combustion temperature. The amount of exhaust gases that are released into the engine is proportional to the load on the engine.
Figure 5: EGR Valve

Mar 20, 2009 | 1995 Mercury Villager

1 Answer

I just bought a 1997 Mercury Sable it was a private sale. Once I got it home the check engine light was on can't remember the code but it when I looked it up it was the canister purge valve. Spent $80. for...


P0401 insufficient EGR flow.

Possible causes:
  • Fault in vacuum supply to EGR vacuum regulator solenoid.
  • EGR valve stuck closed or iced.
  • EGR valve diaphragm leaks.
  • EGR valve or flow path restricted.
  • EGR vacuum hose off, plugged or leaks.
  • VPWR circuit open to EGR Vacuum Regulator solenoid.
  • EVR circuit to PCM open.
  • EVR circuit to PCM shorted to PWR.
  • Differential Pressure Feedback EGR (D.P.F. EGR) sensor pressure hoses both connected improperly.
  • D.P.F. EGR sensor pressure hoses reversed.
  • D.P.F. EGR sensor VREF circuit open.
  • Downstream pressure hose off.
  • Downstream pressure hose plugged.
  • Damaged orifice tube assembly.
  • Damaged EGR Vacuum Regulator solenoid.
  • Damaged D.P.F. EGR sensor.
  • Damaged PCM.



P0443 indicates an intermittent EVAP canister purge valve circuit failure.
Possible causes:
  • Intermittent EVAP canister purge valve or VPWR circuit open.
  • Damaged EVAP canister purge valve.

Mar 13, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...