Question about 2003 Ford F250 Super Duty Crew Cab

Open Question

NEED TORQUE SETTINGS FOR BOLTS ON A 6.0 LITER DIESEL POWERSTROKE. SPECIFICALLY ON THE WATER PUMP AND FAN. I AM CHANGING THE PUMP TODAY. THANKS

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 1035 Answers

SOURCE: torque specifications for head bolts 1995 Jetta 2.0

You should really go to an auto parts place and buy a manual. This something you really should not cut corners. It will give you the specs and the sequence of how to torque the head. You will also need to know how to set the timing in relation to the cam and crank. Manual is well worth the money. It has pictures, instructions, and such.

Good Luck

Posted on Feb 21, 2009

juggernautxt
  • 145 Answers

SOURCE: 04 f250 diesel cranks but won't start

this is an oil pressure problem, either a sensor is not sensing enough oil pressure, or the high pressure pump is not building enough pressure(possibly leaking or head is leaking). this engine requires 450 psi minimum oil pressure at the injectors to actuate the injectors.

Posted on Apr 30, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

drsinister69
  • 2317 Answers

SOURCE: What is the right Torque Specification of the

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings on the 2.5 liter turbo WL diesel cylinder head


cant find that motors engine repair manual today

might be in here... has diesel motors listed

DF]Complete Cylinder Head Torque Specifications for Domestic and ...

fme-cat.com/LiveDocs/99999.pd

Oct 21, 2016 | Cars & Trucks

1 Answer

4610 ford diesel tractor water pump bolt torque settings


First you need to know the diameter of the bolts and the type of thread ie 3/8 N/C or 5/16 N/F then look at the type of bolt ie plain steel or high tensile SAE grade 3, 4, or 6, once you know this go to a general purpose bolt torque chart, and derive the torque spec info.
If the water pump is cast iron use the full torque specification.
If the water pump is alloy then reduce the torque spec 10%

Below is an example of a general purpose bolt / nut torque chart

26186159-4xbrgr0a3wt3vp4m2wlhd0as-1-0.jpg

May 05, 2016 | Ford Cars & Trucks

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

2 Answers

Water pump replacement torque settings


iv never torqued water pump ive always snugged them up pretty good i mean you don't have to stand on the end of the wrench if you use lock tight on the bolts once you tighten them up they wont come loose and you only need a drop of lock tight on each bolt hope this helps you bob

Apr 30, 2011 | 1999 Chevrolet Silverado 1500

3 Answers

How do you replace water pump?


Assuming this is a 460 Ford Big Block:

REMOVAL

-Drain cooling system.
-Remove drive belts.
-Remove bolts attaching fan shroud to radiator.
-Remove fan blade from fan clutch and remove fan shroud.
-Remove fan clutch and water pump pulley from water pump.
-Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Do not remove A/C compressor or power steering pump from A/C compressor mounting bracket.
-Pull A/C compressor mounting bracket forward to remove from stud on water pump.
-Remove bolt attaching generator adjusting arm to water pump. Remove four bolts attaching generator mounting bracket to cylinder head, cylinder block and water pump.
-Remove remaining water pump attaching bolts and remove water pump from engine front cover.
-Remove water pump cover from water pump. Discard water pump housing gasket and water pump cover gasket.
INSTALLATION
-Remove any gasket material from water pump cylinder front cover and separator plate mating surfaces.
-Position new water pump housing gasket and water pump cover gasket coated on both sides with Perfect Seal Sealing Compound B5A-19554-A or equivalent water-resistant sealer meeting Ford specification ESE-M4G115-A.
-Position water pump and water pump cover onto engine front cover. Install bolts and tighten to16-24 Nm (12-18 ft. lbs.).
-Install generator mounting bracket to cylinder head, cylinder block and water pump with four attaching bolts. Install generator adjusting arm to water pump with one attaching bolt. Tighten 7/16-inch bolts to 54-71 Nm (40-53 ft. lbs.) and 3/8-inch bolts to 41-54 Nm (30-40 ft. lbs.).
-Position A/C compressor mounting bracket over water pump stud and secure to cylinder head with four bolts tightened to 54-71 Nm (40-53 ft. lbs.) and secure nut to water pump to 41-54 Nm (30-40 ft. lbs.).
-Install water pump pulley and fan clutch to water pump hub with four bolts. Install fan blade to fan clutch with four bolts. Tighten water pump pulley, fan clutch hub bolts, and fan-to-fan clutch hub bolts to 16-24 Nm (12-18 ft. lbs.). Install fan shroud.
-Install drive belts.
-Fill and bleed the cooling system.
-Start the engine and check for leaks

Jan 10, 2011 | 1997 Ford F350 Crew Cab

1 Answer

Change the water pump. what size is the bolts


Location, size and torque specification for the water pump bolts-3.0L OHV engine...

f2d2658.jpg

  • Install the bolts in the water pump housing.
  • Tighten bolts Nos. 4, 5, 6, 7, 8, 9 and 10to 15-22 ft. lbs. (20-30 Nm). Tighten bolts Nos. 11, 12, 13, 14 and 15 to 71-106 inch lbs. (8-12 Nm).
    The bolts are of different lengths and must be installed in the correct locations.
  • If equipped, attach the engine control sensor wiring to the locating stud bolt.
  • Hand-tighten the water pump pulley retaining bolts.
  • Install the accessory drive belts.
  • Tighten the water pump pulley bolts to 15-22 ft. lbs. (20-30 Nm).
  • Connect the heater hose to the water pump.

Hope this help (remember rated and comment this post).

Apr 10, 2010 | 1999 Ford Taurus

2 Answers

Need to replaCE WATER PUMP 2002 GMC DURAMAX DIESEL how hard?


cardenderek,
This info is totally bogus.You obviousely have never changed a water pump on a 6.6 liter Duramax Diesel engine.1st off it isnt belt driven it is gear driven from the drive train inside the engine.You have to remove the fan shroud,clutch fan assem.,and harmonic balancer as one of the mounting bolts is behind the balancer.Also remove the left side inner fender for easier access.

catD8RII

Mar 12, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

How do I replace a water pump on a 1994 buick park ave


Removal
1. Support the vehicle on jack stands.
2. Disconnect the negative battery cable.
3. Drain the cooling system.
4. Remove water pump drive belt.
5. Disconnect the coolant hoses at the water pump.
6. Remove the water pump pulley bolts (long bolt removed through the access hole provided in
the body side rail), then remove the pulley.
7. Remove the torque axis mount. See TORQUE AXIS ENGINE MOUNT .
8. Remove the water pump attaching bolts and pump.
9. Clean all gasket mating surfaces.



Installation
1. Using a new gasket, install the water pump on the engine. Tighten the bolts to
specifications. See TORQUE SPECIFICATIONS .
2. Install the torque axis mount. See TORQUE AXIS ENGINE MOUNT .
3. Install the water pump pulley, then tighten the bolts to specifications. See TORQUE
SPECIFICATIONS .
4. Connect the coolant hoses onto the pump.
5. Install the water pump drive belt.
6. Fill the cooling system.
7. Add coolant supplement tablets.
8. Connect the battery cable, then start the engine.
9. Inspect for coolant leaks.

Jan 13, 2010 | 1994 Buick Park Avenue

1 Answer

I need directions to change my water pump


drain engine coolant.relieve belt tension .and remove the drive belt.remove upper fan shroud.remove fan or fan and clutch assembly.remove water pump pulley and coolant hoses from water pump.remove water pump bolts.then remove pump from engine.pay attention to bolts location because they are different lenghts.clean water pump gasket mounting surface dont scratch .or pump gasket wont seal and leak .apply sealant to water pump bolts.install water pump with new gasket.if gasket paper put a sealant on it.torque water pump bolts to 30 ft lbs.if you got a 2.2L engine torque water pump bolts to 18 ft lbs.install coolant hoses on pump .install water pump pulley.install fan and fan clutch assembly.install the drive belt .and the upper fan shroud.fill the radiator with coolant.then run engine to check for leaks.WARNING AS A SAFETY PRECAUTION REMOVE NEGATIVE BATTERY CABLE SO CAR WONT BE CRANK BY ACCIDENT. ALSOOOO DONT FORGET TO TURN OFF RADIO FIRST BEFORE DISCONNECTING BATTERY SO YOU WONT LOSE YOUR RADIO CODE.

Jun 01, 2009 | 1999 GMC Jimmy

Not finding what you are looking for?
2003 Ford F250 Super Duty Crew Cab Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...