Question about 2004 Nissan Sentra

1 Answer

How do i go from an old 5 wire 02 sensor to a new for wire sensor in a 04 nissan bsentra

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

Technically you ned 4 wires for a preheated o2 sensor. Positive and ground for your heater and the other 2 are for the sensor itself. Bosch sells aftermarket ones that work very well and at a fraction of the manufacturer cost. Look into those, they may have a 5 wire for you at places like Auto zone, O'Rielly's,etc..

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is a bank sensor for a honda civic ls 04


O2 sensor bank 1 sensor 1 should actually be read as: O2 sensor, bank 1, sensor 1. Meaning the first oxygen sensor (O2 sensor #1) on cylinder bank #1 (it's a Honda inline 4 -cylinder engine, so it only has one bank of cylinders; a V6 or V8 engine would have tow banks arranged in a V shape) needs to be replaced. The oxygen sensor will be threaded into the exhaust near where the manifold (or possibly threaded in at the manifold itself) with some wires coming out of it. In the photo, the O2 sensor is labelled as the air/fuel ratio sensor. 5478b94e-7fcc-4726-9bba-653a172e5a92.jpg

Jun 23, 2014 | 2000 Nissan Frontier

1 Answer

I have a std 5 speed nissan maxima SE 1998, and i change the ECU because when i got the car had the ECU from a automatic maxima so the check engine light it was on, because the car is std, so i change ...


Rear 02 is catalytic convertor here the thing 5 spped and automatic will not make a difference on the engine management it doenst manage transmission control it seperate in the ECM if you have the old one the prom is removable is you dont lets deal with what you got the rear or is a heated circuit so you need to check for 12 volts on the white wire and ground at the black if it all check out then you need to check the signal wire for activity if you get a lot of activivy you got a bad catalytic

Aug 20, 2011 | 1997 Nissan Maxima

1 Answer

2005 toyota corolla. no problems yesterday..this morning it was dead. I can jump it and it turns over but it won't stay running. doesn't seem to be getting any fuel. Which fuse could be causing this...


Fuel Pump-(test for current at the fuel pump using a multimeter or test light while cranking) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Relieve fuel system pressure.
  3. Disconnect the battery ground cable.
  4. Remove the rear seat cushion.
  5. Remove the rear floor service cover mounting screws and remove the cover (except '02-'04). toy_car_cor-02-04fuelpump2.gif

  6. Remove the butyl tape and remove the floor service cover ('02-'04).
  7. Remove the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Remove the fuel line U-clip and remove the fuel line from the fuel pump module.
  9. Squeeze the fuel vent line retainer and remove the vent line from the fuel pump module. toy_car_cor-02-04fuelpump1.gif

  10. Remove the 8 fuel pump module retainer ring mounting screws and remove the retainer ring ('02-'04).
  11. Remove the fuel pump module retainer using special tool 09808- 14020 or equivalent (except '02-'04).
  12. Remove the fuel pump module.
To Install:
  1. Install a new O-ring on the fuel tank.
  2. Install the fuel pump module into the fuel tank.
  3. Use the following procedure to install the fuel pump module retainer ring (except '02-'04). Fuel pump module installation toy_cor-05-18-1203.gif

    1. Align the notch in the fuel tank with the tab in the module.
    2. Matchmark a new retainer with the fuel tank.
    3. Using the special tool install and tighten the retainer ring 2 revolutions.
  4. Use the following procedure to install the fuel tank module retainer ring ('02-'04).
    1. Install the retainer ring on the fuel pump module.
    2. Fasten the retainer with the 8 mounting screws. Tighten 53 in lb (6 Nm).
  5. Install the vent line to the pipe until the fuel vent line connector clicks into place.
  6. Install the fuel line with the U-clip.
  7. Install the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Install the floor service cover with butyl tape ('02-'04).
  9. Install and secure the rear floor service cover with the mounting screws (except '02-'04).
  10. Install the rear seat cushion.
  11. Connect the battery ground cable.
  12. Check for fuel leaks.
prev.gif next.gif

Oct 16, 2010 | 2005 Toyota Corolla

2 Answers

Engine runs like it has a miss fire fault code is p0030 can any one help on ford fiesta 1,4 04 plate


replacing "heated oxygen sensor", (bank 1, sensor 1), on your vehicle is the most likely fix for that.
Seeing how you should only have one bank, then it will be the heated oxygen sensor ahead of the catalytic converter.

Mar 17, 2010 | 2001 Ford Focus

1 Answer

'04 Nissan Altima 02 sensor, cam sensor & air to fuel sensor all


CHECK FUSE TO EGR VALVE CIRCUIT.AND CHECK ECCS RELAY.IF ALL IS GOOD YOU HAVE FAULTY PCM OR ECM CONTROL MODULE.

Jan 07, 2010 | 2005 Nissan Altima

1 Answer

1998 nissan maxima trouble code p0134 the check light is on and it will not pass inspection


The code points to a 02 sensor no responce. It may be dead. Testing can confirm this. If the car has a broken wire or an 02 sensor fuse this also could be the issue.

Nov 10, 2009 | 1998 Nissan Maxima

1 Answer

02 nissan sentra turns over but won't start new


CHECK FOR SPARK AT SPARK PLUGS, CHECK CRANKSHAFT SENSOR, CHECK FUEL PERSURE, ALSO CHECK FOR INJECTOR PLUSATION.

Nov 04, 2009 | 2002 Nissan Sentra

Not finding what you are looking for?
2004 Nissan Sentra Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...