Question about 2004 Jeep Grand Cherokee

1 Answer

Difficulty to open doors with the remote control

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 510 Answers

Replace battery in remote
Look for slot near key ring slot prise open with small screwdriver
After changing battery press unlock button 6 times

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2011 Rav 4 Limited with a keyless start. Ive noticed the doors are not opening with the remote as easily and now Iam having difficulty starting the car. Is there a battery in the remote?


yes there is. Your best bet is to drive the car to a dealership and ask them to do it as the anti-theft system may need recoding.










you

Feb 13, 2017 | Cars & Trucks

1 Answer

Remote car door opener


This sounds like a door lock fault. Will need a replacement lock, or there may be a broken wire in the door to pillar boot.

Jan 17, 2014 | 2008 Volkswagen Golf 1.9

1 Answer

The remote control don´t open the rear door,


IT SHOULD OPEN WITH THE KEY ALSO.












TIM

Dec 20, 2010 | 2006 Chevrolet Equinox

1 Answer

Keyless entry not working


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. Remove key from ignition switch. Close all doors. Open driver's door. Carry out the following within 24 seconds: Turn ignition switch ON and back to LOCK position 3 times. Remove key. Press and release driver's door courtesy light switch 3 times. Ensure doors lock and unlock. If not, wait 40 seconds and repeat procedure starting with driver's door already open. Press each remote control lock or unlock button twice. Ensure doors lock and unlock after each remote control operation. If not, proceed as follows: Press and release driver's door courtesy light switch once. Ensure doors lock and unlock twice. Repeat procedure starting with driver's door already open.
NOTE: A maximum of 3 remote controls can be programmed.

Mar 29, 2010 | 2004 Mazda 6

1 Answer

Trying to remove door latch on 1995 thunderbird. Car has power locks.


inside or outside latch? please rate

Section 01-14A: Handles, Locks, Latches and Mechanisms 1995 Thunderbird, Cougar Workshop Manual
REMOVAL AND INSTALLATION Latch, Door Removal and Installation
  1. Remove front door trim panel (23942) and watershield from front door (20124). Refer to Section 01-05 .
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812) . The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) , if so equipped. Remove the front door latch from the front door .
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch .
  1. Remove front door latch remote control link , front door latch control cylinder rods , and door open warning lamp switches from front door latch , where applicable.
  1. To install, reverse Removal procedure. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).
3e933ef.gif

Item Part Number Description 1 21852 Front Door Latch Push Button Rod 2 21940 Front Door Latch Remote Control Link 3 386656-S Bushing 4 21978 Door Latch Shield 5 218A42 Power Door Lock Actuator 6 22134 Front Door Latch Control Cylinder Rod 7 21812 Front Door Latch
------------------------------------------------------------------------------------
Remote Control Assembly Door Latch
Removal and Installation
  1. Remove front door trim panel (23942) and watershield. Refer to Section 01-05 .
  1. Remove screw and washer assembly retaining front door latch remote control and link (21818) to front door (20124) .
  1. Rotate front door latch remote control and link to remove from front door latch remote control link (21940) .
  1. To install, reverse Removal procedure.

Sep 27, 2009 | 1995 Ford Thunderbird

1 Answer

Remote entry only opens driver door


may be needed reprogramming the remote control

Aug 24, 2009 | 2004 Toyota Camry

1 Answer

Programing garage door openers


Press the button on the garage door opener (red, green, or yellow) until the led starts to blink and within 10 seconds or so, ( I think it's actually 30 seconds) press the GDO control button on the remote and the opener should capture the signal and respond to it from then on. Any remotes that were set to control the opener will be wiped and the new one will be in control. There are instructions that came with the opener that show how to do this from the remote or the key-less entry. If you are talking about an in-car device then your vehicle manual may be needed too, but the main thing is to set the GDO to be looking for the code from the car remote and when you press the in-car remote the garage door should respond. If you have programmed a remote or key-less entry then it is about the same procedure.

Jun 12, 2009 | 2008 Subaru B9 Tribeca

1 Answer

ALARM DON'T WORK WHEN ANY DOOR IS OPEN


There is a way to reprogram your remote but u will have to call the dealer

Jun 02, 2009 | 2001 Jeep Wrangler

1 Answer

Drivers power lock will not unlock with remote.


the door lock actuator is defective, they get really hard to move when they go bad, that is why the difficulty with the key.

Mar 31, 2009 | 2000 Ford Explorer

1 Answer

I cannot open the doors on my BMW using the remote control or the internal button. I can only open the driver's door using the manual key. The remote control locks the door fine and triggers the alarm....


This is a common fault on the series 3 usually down to the General Module 5 or GMV relays breaking down. Item is situated behind glove box reasonably easy to replace. Cost from BMW about £240.00 Can be found through breakers about £60.00. Keys will have to be recoded. See www.bmwgm5.com for more info.
bmmonks

Jul 21, 2008 | 2003 BMW 325

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...