Question about 1998 Isuzu Trooper

1 Answer

Reverse lights only work sometimes on isuzu wizzard

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 642 Answers

Manual gearbox: check on right hand side of gearbox. There's an electrical switch(looks like large nut nut) with 2 wires coming out of it These wires have connectors toward the top of the gearbox, diconnect them.
The wires that this switch was connected to, conect them to each other. ie the reverse light switch has been bypassed. Put the vehicle in reverse. Turn on the ignition. DO NOT START. Check the reverse lights. If on the switch is faulty and needs to be replaced. If not measure the voltage across each of the wires and a good earth point. (Gearbox casing will do fine. ) One of the wires should read < 12V.
If 12V then

  • Globes are faulty(Replace)
  • wiring to the globes are faulty - unlikely -(This can be repaired by simply running a new wire to the globes)
If no 12V then the wiring to the fusebox is faulty. A quick fix is to run a new wire from the fusebox to the switch(Connect to fuse C-3, indicated as "turn, back")

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4wd switch stays on


sometimes after using four wheel drive the light stays on you can put in reverse and it usually goes out if not the sensor maybe bad its located on the front axel mine had a broke wire

Apr 18, 2014 | 2004 Isuzu Rodeo

1 Answer

Hi, I have an 89 Isuzu Bighorn shortwheel base model, the rear tailights will not work? I have checked all fuses and replaced all bulbs still no luck. The turn signals and reverse and brake lights all...


Check for power and ground on the backside of the light socket. Possible broken wire somewhere. Also look for corrosion (green death) at the tabs that make contact with the bulbs.

May 04, 2011 | 1989 Isuzu Trooper

1 Answer

Turn signals reverse lighs dont work need a wire diagram for this 1997 izuzu rdeo 4x4


Reverse light are operated by the range selector switch on the side of transmission aka. gear selector lever. A problem with the t/s lights would be in the turn signal combo switch.

Jan 11, 2011 | 1997 Isuzu Rodeo

1 Answer

Back up lights won't work on 2004 Isuzu Rodeo. Bulbs and fuses are all good.


check the reverse switch which is connected to the back of transmission. it may be disconnected or have a broken switch.

Jan 05, 2011 | 2004 Isuzu Rodeo

1 Answer

I have a 2003 isuzu rodeo. Sometimes it is hard to put into reverse. I can usually get it to work in 1 or 2 tries. the abs light came on a couple of times. what could make this happen?


I do not think shifting gears ,putting your car in reverse has nothing to do whit whit the abs to come on and off ,my isuzu rodeo did the same thing and it was a dirty sensor ABS on front wheels , There is a ring on the inside of the front disc's that works together with the ABS sensor to send information to the car computer when braking ,and must have a distance of about 1/8 of an inch between ring and sensor ,,they must not touch ,what happens is that over time dirt starts to build between sensor and ring ,and ring and sensor begin to touch ,and if they do touch ABS light will start be on and off while driving ,,most of the time the problem is the sensor and not necessarly a bad sensor ,,only a durty sensor and dirty ring ,a broken or loose wire also will activate the ABS light ,,,and about car hard to put into reverse ,you'll probably need a new clutch ,,good luck

Sep 18, 2010 | 2003 Isuzu Rodeo

2 Answers

Check trans light on....no power


My brake lights are out, the back, reverse, and head lights all work. My steering is fine as well as my brakes. But the warning lights for brake and ABS light up on my dash board

Feb 17, 2010 | 1992 Isuzu Trooper

1 Answer

1995 Isuzu Rodeo 4X4 3.2 5 speed manual, reverse lights on in 1st


the wiring on the gear box is connected to switches wrong, there bullet head connectors red to red wiring and blue to blue from switch to loom is correct
both wires on one switch are red connect these to the 2 red wires one has colour trace on it also. the other switch blue wires to blue wire on loom with possibly another colour wire but they are together. you cant go wrong the connectors are male on one wire and female on the other on each switch(detent switch)

Nov 22, 2009 | Isuzu Rodeo Cars & Trucks

2 Answers

Hi I HAVE A ISUZU WIZZARD 3.0 WITH 4jx1 engine,it hard to started,diesel knock when it idle,engine light stay on with a code p10193 or p1393,already replace fuel filter,engine oil,train and renew a diesel...


Hi, you problem is the rail oil pressure sensor having a high voltage input -  P0193 code set . This will also cause your faults . 
Change the sensor which is under the cam cover and the smaller of the two there and it will run ok .
You need the sensor set up on a tech II after fitting to run at its best.

Oct 02, 2009 | Isuzu Trooper Cars & Trucks

1 Answer

My 2000 isuzu trooper reverse lights always stay on no matter what gear I am in. I need to know where to find the reverse light switch.


usually only 2 places it can be,,,under the car near the gear shift.....or under the centere consol inside the car, where the gear shift is, need to remove part of the centre consol to get to it

Jul 30, 2009 | 2000 Isuzu Trooper

Not finding what you are looking for?
1998 Isuzu Trooper Logo

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...