Question about 1996 Jeep Grand Cherokee

1 Answer

I replaced front track bar and stabilizer and now makes clanging sound when i make sharp left turn and doesnt turn for a coupel seconds when you turn to the right.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

Sounds like a hub bearing. Jack up the front end and place a hand at the top and bottom of each front tire. Try to make the top or bottom of the wheel move inward and outward. This shouldn't move very much at all. The tolerance is measured in .000 of an inch. So if there is any significant movement, the hub bearing has failed. Another good part to check are your ball joints. If the hub isn't your problem, drop me a line and I'll tell you the procedure for checking the ball joints.

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front end vibration


its your track bar and steering dampener at low speeds the front axel walks side to side and the dampener cant compensate for the travel at hiway speed the dog track is caused by the track bar not keeping the front differential in place and alow ing it to wander and the shuttering you get is from stabilizer being week replace them first and let me know

Feb 27, 2014 | Dodge Cars & Trucks

1 Answer

A loud metal to metal clanging noise in the front of the car


Are you sure the struts and strut bearings are installed correctly and all fasteners are tight? Did you check your stabilizer links? Did you check your stabilizer frame bushings? Did you check your tie rod ends? Did you check the lower ball joints? Did you check the control arm bushings? Did you check for loose or missing brake caliper bolts?

I am sure that a thorough inspecton of the front steering and suspension system will turn up something. However, it is really hard to accurately guess from this end without more to go on than just a "metal clanging noise"....there are way too many things that can fit that desription.

Apr 09, 2012 | 2006 Pontiac Torrent

1 Answer

What does the control arm on the front left driver side supposed to look like fully assembled


Hello! First diagram is the lower...Second is the upper..Guru...saailer

LOWER IDENTIFICATION:




Item
Part Number Description 1
5495 Stabilizer Bar Link Bolt and Bushing Assembly 2
18A192 Nut, Washer and Bushing Assembly 3
808264 Bolt 4
5005 Frame 5
5B326 Torsion Bar (LH) 6
5B327 Torsion Bar (RH) 7
620481 Nut 8
5C491 Nut and Washer 9
3079 Front Suspension Lower Arm (LH) 10
3078 Front Suspension Lower Arm (RH) 11
3A130 Tie Rod End 12
808166 Nut 13
808167 Nut 14
5K483 Front Stabilizer Bar Link 15
5482 Front Stabilizer Bar 16
5484 Front Stabilizer Bar Bushing 17
3B353 Front Stabilizer Retainer 18
N807396-S100 Bolt A
- Tighten to 40-55 Nm
(30-40 Lb-Ft) B
- Tighten to 150-200 Nm (111-148 Lb-Ft) C
- Tighten to 21-29 Nm
(15-21 Lb-Ft)


UPPER IDENTIFICATION:
Item Part Number Description 1 3C156 Damper Assembly (RH) 2 805348 Nut and Washer 3 - Shock Absorber Insulator
(Part of 18198) 4 3C157 Damper Assembly (LH) 5 3020 Front Suspension Bumper 6 3083 Front Suspension Upper Arm Assembly A - Tighten to 34-47 Nm
(25-35 Lb-Ft)



LOWER DIAGRAM FOLLOWED BY UPPER:

2_12_2012_9_47_51_pm.gif2_12_2012_9_54_26_pm.gif

Feb 12, 2012 | 1996 Ford Explorer

2 Answers

I have a 98 millenia with front end problems. It makes popping noises while driving on rough roads and some smooth roads. It sounds like the front end about to come out of it. I've already changed the left...


sounds as though the rubber bushings (there are two of them L/R side on the stabilizer bar) could be the issue. When the bushing are loose they allow the stabilizer bar to bump against the steering or rack and pinon.

Sep 14, 2010 | 1998 Mazda Millenia

2 Answers

Hello, I am experiencing a "death wobble" with my 2007 Jeep wrangler 2 door. On occasion, while driving about 40 mph my jeep and steering wheel **** left and right, violently, after hitting a bump. Does...


Cgeck for play in the track bar , it goes from frame to front diff. Get a friend to move the steering wheel from left to right ( engine off ) about an 1/8 of a turn back and forth and watch for play in the steering and suspension parts. good luck.

Jul 28, 2010 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

Replace broken sway bar for a 1996 ford windstar


Section 04-01: Suspension and Wheel Hubs, Front 1996 Windstar Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise and support the vehicle. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Using care not to damage the front stabilizer bar link ball stud seal, remove the RH and LH front stabilizer bar link-to-front shock absorber nut.




  1. Using care not to damage the front stabilizer ball link stud seal, remove the RH and LH front stabilizer bar link-to-front stabilizer bar nut.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage the ball joint boot.
    With another set of support safety stands under front sub-frame, remove two rear sub-frame retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).
  1. Remove front stabilizer bar bracket bolts, stabilizer bar brackets, stabilizer bar bracket insulators and front stabilizer bar (5482) as required.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar bracket insulator installation position.
  1. Lubricate inside diameter of new stabilizer bar bracket insulator with Rubber Suspension Insulator Lube E25Y-19553-A meeting Ford specification ESF-M99B112-A or equivalent. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber stabilizer bar bracket insulators.
  1. Install new stabilizer bar bracket insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on stabilizer bar bracket insulators and install new bolts. Tighten to 55-63 Nm (40-46 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Tighten to 115-132 Nm (85-97 lb-ft).
  1. Install front stabilizer bar link (5K483) to front shock absorber. Use care not to damage link ball joint boot seal.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Install a new front stabilizer bar link-to-shock absorber nut. Tighten to 90-100 Nm (66-74 lb-ft).

  2. 66a0f1a.gif

Apr 28, 2010 | 1996 Ford Windstar

1 Answer

Loud popping sound when turning left


I recently had the same problem, it ended up being the front stabilizers and the drive shaft.

Oct 26, 2009 | 1999 Chevrolet Tracker

1 Answer

Noise from rear suspension on 2003 Honda Odyssey.


a clunking clanging noise sounds very much like your stabilizer bar end links and bushings. you have a thin rear "sway" bar on the rear of your odyssey. this can cause a whole lot of noise. grab each side and pull/push. if it feals loose, replace the end links and bushings.

Oct 25, 2009 | 2003 Honda Odyssey

1 Answer

Vibration in front end


It is likely both your track bar and the lack of a steering gear box stabilizer. The bushings on your stock track bar can be replaced with polyeurethane or metal bushings which will help curb the problem.
The steering stabilizer attaches to your steering gear box and your frame allowing the steering to be more stable. I have put both on my truck and it drives like a caddy now as a result. If I had to choose between the two items, my money would go to the steering stabilizer first. I believe I bought mine here:
http://www.xtremediesel.com/bd-powerperformancedodgesteeringstabilizer.aspx
Hope this helps

Apr 05, 2009 | 2006 Dodge Ram 2500

1 Answer

When pressing accelerator steering pulls to the right and when brakingor accelerating knocking sound coming from front left wheel


worn anti roll bar bushings and worn track rod end ..these keep the longitudinal stability of the wheel and the shock absorber gives horizontal stability..hope this helps..

Dec 07, 2008 | Volkswagen Golf Cars & Trucks

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...