Question about 2001 Ford Escape

1 Answer

Wat is a dpfe sensor - 2001 Ford Escape

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

It tells the ecm if the egr valve is opening or not. I can tell you where its located if you tell me what size engine you have. It is a common failure on fords. It won't cause the engine to run bad or cause any problems when it goes bad, it will just bring on the Check engine light.

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code PO401


Exhaust gas recirculation module check:


1. Note the Differential Pressure Feedback Exhaust Gas Recirculation (DPFE) sensor voltage through the scan tool or backprobe the Brown/Light Green (BN/LG) wire of the Exhaust Gas Recirculation System Module (ESM). Voltage should indicate a reading of 0.5-1.2 volts.

2. If the voltage of the DPFE sensor is out of range, low or high, disconnect the ESM and note that the voltage of the DPFE sensor circuit should indicate a reading of 5.0 volts.

3. If the DPFE sensor voltage is out of range connected and the reading shows 5.0 volts with the ESM disconnected, reconnect the ESM and verify that the Brown/White (BN/WH) wire shows a 5.0 volt reading and that the Grey/Red (GY/RD) wire shows to be a good ground, indicating a voltage of less than 0.1 volts. If these circuits check to be ok, replace the ESM due to a faulty DPFE sensor.

4. If the DPFE sensor voltage in step 1 is found to be ok, verify that both vacuum hoses to the ESM have full engine vacuum to them when it's running.

5. With the engine idling, backprobe the Brown/Pink (BN/PK) wire and hold it to ground. This should activate the Exhaust Gas Recirculation Vacuum Regulator (EVR) solenoid of the ESM. The EGR valve should open, the engine should run rough, and the DPFE sensor voltage should climb.

6. Replace the ESM for a faulty EGR valve, EVR solenoid, or DPFE sensor if the DPFE sensor or engine does not respond to ground activation of the BN/PK wire

Nov 10, 2013 | 2004 Ford Explorer

1 Answer

1401 egr code


P1401 FORD - DPFE Sensor Circuit High
Faulty Differential Pressure Feedback Electronic (DPFE) sensor
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection. This is not likely the EGR but the EGR pressure sensing valve.

Oct 19, 2012 | Cars & Trucks

1 Answer

I have a tropubleshooting code of P1405. On a ford Expedition 5.4l. Where do i fine the DPFE sensor (DPFE sensor upstream hose off or plugged.. aaECM detected EGR flow in a negative direction with aan


DPFE sensor failures are VERY COMMON on Ford vehicles. However, clogged EGR ports are also very common on 5.4L Ford engines. The DPFE sensor is located on the left side of the engine. It connects to two silicone rubber hoses that connect to the steel EGR tube coming from the back of the engine to the EGR valve. (See picture of the sensor below)

Another common failure is a DPFE sensor that has melted due to excessive exhaust back-pressure. If you find the DPFE sensor melted, suspect a restricted exhaust. (smashed tailpipe, clogged catalytic converter, etc..)


12_29_2011_3_03_10_am.jpg

Dec 29, 2011 | 2002 Ford Expedition

1 Answer

Have a dtc p1401


Diagnostic Trouble Code (DTC) P1401 indicates that Self-Test has detected DPFE sensor circuit input above the maximum.

Possible causes:

-- DPFE SIG open.

-- DPFE SIG shorted to VREF or PWR.

-- VREF shorted to PWR.

-- SIG RTN open.

-- Damaged DPFE sensor.

-- Damaged PCM.

dpfe_sigs.jpg

Dec 09, 2011 | Cars & Trucks

2 Answers

I have a sensor on an 03 Ford Explorer...part # 4u7e-9j460-aa7d19aj397m7997. What sensor is this?


This is the DPFE(Delta Pressure Feedback) sensor. Some places may call it an EGR(Exhuast Gas Recirculation) sensor but that's not really what it is.

Mar 29, 2011 | 2003 Ford Explorer

3 Answers

Wat does code p1400 means


In order to give you accurate information. I need size of engine example 2.0 L 3.0L. but code P1400 means Differential Pressure feedback EGR circuit low input. Maybe your differential oil is low.

Apr 01, 2010 | 2002 Ford Taurus

2 Answers

Check engine light with code p1401


Recirculation (EGR) valve codes. The Differential Pressure Feedback EGR (DPFE) sensors on these vehicles have a high failure rate. Ford now uses a redesigned DPFE sensor. In effect, since the failure rate is so high, if you get this code, replace the sensor and retest. When the DPFE Sensor starts failing, it gives the PCM bad information. The DPFE Sensor is less sensitive, and the PCM thinks less recirculated gas is being burned than is actually so. Trying to compensate, the PCM opens up the actuator too much. This excessive amount of EGR combined with the air coming in via the throttle body leans out the fuel mixture, causing a lean misfire, which is the "stumble" or "hesitation" that is common as the DPFE Sensor fails. The DPFE sensor in the Focus is not very robust, requiring frequent (every 30k miles or sometimes less) replacement or a work around. Note that complete DPFE sensor failure is a very slow process, and the check engine light won't come on until the DPFE sensor is pretty much done for. If you're experencing stumble or hesitation while cruising, and think that it might be related to DPFE sensor failure. If the stumble goes away, then your DPFE sensor is more than likely failing. Of course, replacement of the bad DPFE sensor is the official recommended fix for this problem.

Jul 29, 2009 | 1998 Ford Ranger SuperCab

1 Answer

I am having trouble getting my check light to go off after I had it checked and the EGR valve was replaced. The light comes back on after about 15 miles of driving and the code reads EGR poor flow. I can...


Insufficient EGR Flow Detected

Possible Causes:
DPFE sensor signal circuit is shorted to ground
DPFE sensor VREF circuit is open between sensor and PCM
DPFE sensor downstream hose off or plugged
DPFE sensor hoses both off, loose or damaged
DPFE sensor hoses connected wrong (reversed)
EGR orifice tube is damaged or restricted
PCM has failed
And what sets the code is…….Engine started, engine running in closed loop under steady cruise conditions, and the PCM detected the DPFE sensor input indicated insufficient EGR gas flow. Run the KOER Self-Test, and if DTC P1408 is present, the fault is currently present. This code sets in 2 Trip(s). The light will stay on until the cause is repaired. A bad EGR valve is only on possible cause.

Hope this helps,

Dave

Feb 28, 2009 | 2002 Ford Mustang

2 Answers

2002 ford focus p0401


Here is a list of possible causes for a PO401, hope this helps.

  • DPFE sensor signal circuit is shorted to ground
  • DPFE sensor VREF circuit is open between sensor and PCM
  • DPFE sensor downstream hose off or plugged
  • DPFE sensor hoses both off, loose or damaged
  • DPFE sensor hoses connected wrong (reversed)
  • EGR orifice tube is damaged or restricted
  • PCM has failed

Feb 10, 2009 | 2000 Ford Focus

2 Answers

DPFE Sensor with codes PO401 And PO402


The DPFE is located near the EGR valve, it has 2 very thick silicone rubber hoses connected to it that come off the exhaust. It is rectangular and about 1/2 the size of a pack of smokes

Nov 12, 2008 | 2001 Mercury Sable

Not finding what you are looking for?
2001 Ford Escape Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...