Question about 1995 Ford Escort

1 Answer

What are timing marks on camshaft pulley for 1995 ford escort 1.9 li

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

There is a pointer in one of the holes in the center of the cam pulley that lines up with a dot on the cylinder head

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1977 ford pinto timming marks


Hope this helps. Please don't forget to rate....thanks!



c17hydro_169.gif

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


CAUTION:

After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
c17hydro_170.gif

Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

May 08, 2011 | Ford Mustang Cars & Trucks

1 Answer

How do you line up the timing gear in a 98 ford escort?


Hi.
Rotate the engine until the Timing mark on the Crankshaft pulley, is in line with the Timing mark on the Bottom casing.
Rotate the camshaft pulley until that Timing mark is in line with the Mark on the Camshaft bearing casting.
Install the timing Belt from the RH side, with no looseness in the Straight line tension, depress the Tensioner pulley, and feed the belt around the Water pump drive, and then the tensioner.
As you release the tension on the Tensioner pulley, ENSURE that neither of the Timing Pulleys MOVE.
Rotate the engine 2 times and check that the Timing marks at Top Dead Center are still ALIGNED.
If all is in good order, reinstall the Motor Mount and Belt covers and ancillaries.
Regards, DT

Mar 25, 2011 | 1998 Ford Escort

1 Answer

Where should timing mark on camshaft be on 1999 ford escort single overhead


Support the engine with the floor jack and remove the right hand side motor mount and bracket. Raise the engine slightly and remove the timing belt cover and the crankshaft pulley bolt and the pulley. Turn the engine clockwise until the crankshaft timing marks are lined up. There is a triangular mark on the crankshaft and a plate with a mark at 12 o'clock on the block. The camshaft has a triangular mark on the sprocket and a dot on the block at 12 o'clock that must line up.

Jan 29, 2011 | 1999 Ford Escort

1 Answer

I need to know the timing marks on a 1995 escort 1.9l


The timing marks are on the timing cover for the crank pulley, and on the cyl head for the cam

Dec 05, 2010 | 1995 Ford Escort

1 Answer

How to set the time belt?


4 Cylinder diesel(4JX1) :
1 - Timing mark
2 - Cam pulley
3 - HP Oil pump pulley
4 - Tensioner pulley


suzman_0.jpg

6 Cylinder petrol:
Align crank(C) timing notch mark (1) to oil pump mark.
Align cam pulley(L+R) marks(3) to cylinder head marks
The cam belt has 3 marks, 2 lines and one mark that is actually a row of dots. Align the dots to the crank pulley groove mark(2) and align the other 2 lines to the cam pulley marks. Using a clothes peg to hold the belt to the cam pulleys works wonders to keep it in place while fitting. Please note the arrows on the belt and have them point in the direction of rotation - right to left side of engine
W - water pump pulley
I - Idler pulley
T - Tensioner pulley.

If for some reason you need to realign the cams on each bank :
Standing in front of the car and starting from YOUR left , looking at the cams you should see RE, RI, LI, LE on each of the camshafts.(R for right bank, L for left bank, I for intake and E for exhaust) Right bank camshafts are marked with one dot, left bank with 2 dots on the shaft itself. To align the camshafts to each other each cam shaft gear has a mark on it. Draw an imaginary line between the centre of the camshaft and the centre of the pulley. The alignment mark should be between the two along this imaginary line. The result will be that RI an RE will be at the top of each gear. The same with the left bank.


suzman_2.jpg

Nov 08, 2010 | 1998 Isuzu Rodeo

2 Answers

Need a picture of the crankshaft and cam shaft alignment marks


Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

72dd798.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

a41ca11.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

2022a8b.jpg

I hope helps with this (reemmber rated this help) Good luck.

Dec 29, 2009 | 1997 Ford Escort

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

How do you align the camshaft & crankshaft timing marks 1.9


This is the same as a Ford Escort 1.9, the #1 cylinder should be all the way up. To confirm- the crak shift mark should be on zero which is Crank Shift Center- THe camshift sproket should align with the headmark. Make sure both marks don't move. Align the belt- not too tight , not to loose

Jul 12, 2009 | 1995 Mercury Tracer

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

Not finding what you are looking for?
1995 Ford Escort Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...