Question about 1991 Plymouth Sundance

1 Answer

Fuel pump not pumping fuel ( new pump) - 1991 Plymouth Sundance

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 14,036 Answers

CHECK FUEL PUMP FUSE LOCATED BEHIND THE STEERING COLUMN ABOVE THE HOOD LATCH LEVER.IF FUSE GOOD REPLACE THE AUTO SHUTDOWN RELAY LOCATED ON INNER FENDER PANEL NEAR THE BATTERY.IF ALL IS GOOD SCAN CAR FOR ECM FAULT CODES.

Posted on May 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WE PUT NEW FUEL PUMP ON B2300 MAZDA 1994 YOU PUT GAS IN THE THROTTLE AND IT RUNS BUT WILL NOT START NO OTHER WAY


New pump may be bad--it happens. There should be a check valve that keeps fuel from draining back when you turn it off. If this is not working it could cause this.

Oct 17, 2016 | Mazda B2300 Cars & Trucks

1 Answer

2000 chevy truck 3500 check wiring on fuel pump harness


images for 2000 chevy truck 3500 check wiring on

How to Install New GM Wire Harness on Fuel Pump Module ...

? 3:10
https://www.youtube.com/watch?v=FffdzqknP3k
Apr 20, 2012 - Uploaded by Airtex Pumps
This video is about how to install a new Airtex fuel pump module into some GM ... fuel pump and gas tank to a 98 internal fuel pump and gas tank on my truck 88 gmc. the wires are a little different. .... Check the power & ground at the pump. ... CHEVY SILVERADO FUEL PUMP CHANGE OUT.2500HD 2001.

How to test an electric fuel pump - YouTube

? 13:54
https://www.youtube.com/watch?v=Q3ZiTsKCdO8
Feb 3, 2012 - Uploaded by ScannerDanner
2001 GMC 3500 8.1L engine with no fuel pressure. In this video I am showing how to test the fuel pump electrical circuit using atest light and scan tool. ... seconds on the ground wire. when i unplug the harness from the the fuel pump .... need help newfuel pump chevy venture 2004 runs for a few days then ...

How to Install Fuel Pump E3947M in 1997-2000 Chevrolet ...

? 5:53
https://www.youtube.com/watch?v=9LLLRVnItbI
Apr 20, 2012 - Uploaded by Airtex Pumps
Applications: 2000-97 CHEVROLET/GMC C, K 1, 2, 3 TRUCK 262... Please check out our 'How to Install New GM Wire Harness onFuel Pump ...


Jan 22, 2016 | Cars & Trucks

1 Answer

We have replaced fuel pump in a 98 ego metro LSi drove home ran fine. Now it won't start any ideas why it won't start.


Pam, was the fuel filter replaced at the same time that the fuel pump was replaced? If not, replace the fuel filter. Often, the filter will get clogged with debris. When that happens, the fuel pump will be ruined. Replacing the pump without replacing the fuel filter can ruin the new pump. It is also possible that your new fuel pump is defective. Now that most replacement parts are made in China and the third world, there is virtually NO quality control. I'm a professional mechanic and defective brand new parts are a BIG problem in this industry. Was the fuel pump relay replaced when the new fuel pump was installed? Always install a new relay, as a failing [your old] fuel pump will often damage the relay. This will cause problems with the new fuel pump. I would advise that you install a fuel pressure test gauge to the engine. This will allow you verify whether or not the engine is receiving enough fuel pressure. If the pump works but the pressure is low, also check the fuel pressure regulator. The web links below should help you.


How to Check for Fuel Delivery in Geo Metro eHow

FYI, there is also a "sock" style pre-filter on the fuel pump. This also needs to be replaced any time that you replace the fuel pump.

Mar 13, 2015 | Cars & Trucks

1 Answer

1999 chevy silverauto quits running no fuel pressure. new fuel pump new filter. Can't figure it out


might be a bad fuel regulator.. or your fuel pump relay might be going bad.. and also where did u get your fuel pump from.. i ran into a problem where i had to replace a fuel pump 3 times before i finally got on that worked right..

Apr 29, 2012 | Chevrolet Cars & Trucks

1 Answer

1994 ford explorer, new fuel pump,new fuel pump relay,no power to fuel pump


Have you checked the fuel ppm cut off switch? It should be under the passenger side of the dash. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 21, 2012 | Ford Explorer Cars & Trucks

1 Answer

Ran out of gas in 92 prizm...new fuel pump, new fuel filter, theres fire in plugs, fire in fuel ignitors, what could the problem be...


IF YOU RAN OUT OF GAS WITH NEW FUEL PUMP.MORE LIKELY YOU DAMAGED NEW FUEL PUMP NEVER NEVER RUN OUT OF GAS.GAS KEEP FUEL PUMP COOL AND KEEPS FUEL PUMP LUBRICATED

Sep 18, 2011 | 1992 Geo Prizm

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

2 Answers

It will not start. We changed the fuel pump three times. Each time the new fuel pump will not hum or buzz when you turn the igntion.


Did you check the fuel pump wiring harness, fuel pump ground , power to the fuel pump, fuel pump fuse , fuel pump relay

Oct 18, 2009 | 1999 Chevrolet Venture

Not finding what you are looking for?
1991 Plymouth Sundance Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...