Question about 1992 Honda Civic

1 Answer

How to repace distributor on 1988 honda civic. se

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

Remove the distributor cap and mark the distributor housing where the rotor is pointed to, and the distributor to where it goes into the head. Unplug the distributor, and remove the ditributor hold down bolts. Install the distributor with the rotor and distributor pointing to the marks made before removal.

Posted on May 31, 2010

Testimonial: "Thank you"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Took need firing order on 1988 honda civic removed spark plugs wires distributorcap dont know witch wire goes where


what size engine.. do you have new wires... you need the number off the wires so you can put them in properly... because each wire will go to specific cylinder and place on the distributor

Jan 28, 2011 | 1998 Honda Civic

1 Answer

Honda civic 1988 wont start stopped just after starting has power to all non-ignition circuits - horn / headlights / brakes / etc but no dash lights / no solenoid ignition click starter and solenoid 10 amp...


I'd check the distributor for spark, those year Honda's had alot of problems with the distributors. Also, I would check the multi-relay, under the dash, on the driver side, on the far left of the dash.

May 29, 2010 | 1998 Honda Civic

2 Answers

Have a 97 honda civic, hard to steer.repaced p/s pump


hard to steer is not the pump in most cases, it is the power steering rack and pinion steering gear.

May 05, 2010 | 1997 Honda Civic

1 Answer

Removing honda civic distributor cap & assembly.


The distributor is driven directly by the camshaft. The end of the camshaft contains a set of grooves that engage the distributor shaft. These grooves prevent the distributor from being incorrectly installed.

REMOVAL & INSTALLATION
  1. Using masking tape, remove the spark plug wires from the cap and number them for installation as they are removed.
From 1988-onwards, all Honda Civic series models were fuel injected.
  1. Disconnect the vacuum hoses, the primary wire and the high tension wire. If equipped with fuel injection, remove the four prong connector from the crank angle sensor.
  2. Remove the hold-down bolt(s) and pull the distributor from the head.


5d08c31.jpg

Fig.: Distributor mounting -1992-95 vehicles

033d862.jpg

Fig.: Pulling the distributor from where it mates to the camshaft at the right side of the valve cover

Hope helped (remember rated this help) Good luck.

Oct 21, 2009 | 1992 Honda Civic

2 Answers

I have a 88 honda civic wont staying running i replace to ingtor and coil looks good.. computer light flashes 15 times and stops. then 15 again. what code is that? and what senor that could be?


what about the distributor pickup? have u replaced that, also pull the steering column covers and see if the ignition starter swtich has come apart, very common on this year.

Sep 10, 2009 | 1988 Honda Civic 2 Door

2 Answers

1988 honda civic 1.5eng.cut off now will not start it


You need a cap and rotor. Rotor is probaly grounding thru distributor shaft from a carbon track.

Jun 10, 2009 | 1991 Honda Civic

1 Answer

Vehicle will start but after it gets warmed up it will not start


i had the same prblem with my 88 honda civic i found out that honda recalled the distributor for that year because the ecu or ecm inside the distributor burns out faster thn normal hope this helps

Nov 16, 2008 | 1988 Honda Civic 2 Door

Not finding what you are looking for?
1992 Honda Civic Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...