Question about 2004 Dodge Dakota

2 Answers

Location of the throttle position sensor

Where is the throttle position sensor located on a 2004 Dodge Dakota with a 3.7 liter / V6 engine?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 438 Answers

The censor is located adjacent to the throttle control linkage, and has a 3 wire connection plug

Posted on May 30, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Bad gas mileage on 2004 dodge Dakota any ideals

Posted on Jan 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the throttle position sensor located on a 91 Dodge Dakota


need info on which engine, in general, it is usually located near the throttle linkage, on the end of the throttle shaft, of the Air intake,. usually held on by 2 screws, and having a 2 or 3 wire connector.

Dec 16, 2015 | Dodge Cars & Trucks

1 Answer

Location of the iat sensor for a 2005 dodge dakota v6


It on the engine manifoldon the left side of intake manifold plenum use diagram its number 3cansmo_54.gif

Aug 24, 2011 | 2005 Dodge Dakota

1 Answer

Where is the location of the coolent temp. sensor on a 04 dodge truck v6 3.7 . I need to replace it.


Dodge Dakota 3.7L v6:




0996b43f80204b36.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. ECT sensor location-3.7L, 4.7L engines.

icn_arrow.gifBack to Top Inspect/Test/Replace Because ECT (engine coolant temperature) sensor procedures vary depending upon their location, first locate the part. You may need to partially drain the engine coolant to prevent coolant spillage.

  • Disconnect the negative battery cable.
  • Unplug the ECT.
  • Then, unscrew it.
  • Reverse the removal procedures to install the new part.
  • Connect the negative battery cable to the battery.

Feb 15, 2011 | 2004 Dodge Ram

1 Answer

I am stupid when it comes to cars, just to warn you. i need to know exactly how to get to my crank sensor on a 1991 3.9L Dodge Dakota 2wd auto.


V6 and V8 engines
See Figure 3
  1. Remove the air cleaner assembly.
  2. Unplug the wire from the sensor.



0900c15280070e13.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Crankshaft position sensor location-V6 and V8 engines

  1. Unbolt then remove the sensor from the engine.

To install:
  1. Position the sensor to the engine, then install the mounting bolts, tightening them to 70 inch lbs. (8 Nm).
  2. Install the air cleaner assembly.

***This can be viewed at autozone.com. become a member and look up repair guide for crankshaft postion sensor. *** be sure mounting surface is clean before installation.

Jan 03, 2011 | 1995 Dodge Dakota

1 Answer

Where is the crankshaft sensor located on the dodge dakota 99 sport v6


On the V6 and V8 engines, the crankshaft position sensor is bolted to the cylinder block near the rear of the right cylinder head.

2e977ab.jpg

Jul 30, 2010 | 1999 Dodge Dakota

1 Answer

Location of oxygen sensor on 2004 dodge dakota


One of them is located on the driver's side of the motor and connects to the exaust manifold.

May 22, 2009 | 2004 Dodge Dakota

1 Answer

Crank position sensor location


should be on bell housing on thr driver side

May 13, 2009 | 2003 Dodge Dakota Club Cab

1 Answer

2004 dakota won't start


sounds like a crankshaft position sensor..fairly common problem on these 3.7 engines..check for fault codes in engine controller..can mbe hard to get out of engine block..seize in..sometimes have to come out in pieces..it is located on passenger side rear of engine..1 bolt holds it in..3 wire connector..below exhaust manifold in side of block..fairly inexpensive part..recommend dealer part

Apr 26, 2009 | 2004 Dodge Dakota

3 Answers

Location of Crank Sensor


Front of the engine near the the timing chain cover, this is a picture. Make sure the connector is clean and free of corrosion.



300? 300: true ); MAX-HEIGHT: 400px; ; HEIGHT: expression(this.height > 400? 400: true )" src="http://info.rockauto.com/getimage/getimage.php?imagekey=1005895&imageurl=http%3A//www.standardbrand.com/web_app/catalog/images/PC127.jpg" />

Aug 04, 2008 | 1997 Dodge Dakota

2 Answers

Cant find crank position sensor on 1991 dodge dakota with a 3.9 liter engine 2wd auto.


Can not find crank sensor on 1995 Dodge Dakota how hard is it to replace

Jul 24, 2008 | 1995 Dodge Dakota

Not finding what you are looking for?
2004 Dodge Dakota Logo

Related Topics:

607 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...