Question about 2000 Oldsmobile Intrigue

1 Answer

Rear power window drive cable

Oldsmobile 2000 Intrigue drivers side rear power window. The original problem was the bracket that holds the ends of the up and down cables broke allowing the up window cable pull out of the bracket. I repaired the bracket so that the cable will not pull out but with both ends in the bracket I can get only one cable in its track. It appears that the down window cable should go in last but I can not get enough slack to get in the track.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 110 Answers

Hello there:
i think that you may want to go ahead and replace the actuator and motor this would solve the problem and keep from having troubles later on down the road it should come with the track cables and all i hope this helps you out ..... if you would please leave a review for me thanks sincerely D.Jones

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat stopped working in 2000 Oldsmobile intrigue. What could it be? I can't find the blower or HVAC relay and all fuses are good


fuse for the heater fan on a 2000 Oldsmobile Intrigue located. Passenger side, open the front door. On the side of the dash. These videos should help you locate them.
Interior Fuse Box Location 1998 2002 Oldsmobile Intrigue 1998 Oldsmobile...

Nov 17, 2016 | 2000 Oldsmobile Intrigue

1 Answer

Instructions how to step by step replace ignition lock cylindor for an 1999 oldsmobile intrigue


1999 Oldsmobile Intrigue

IGNITION SWITCH AND LOCK CYLINDER REPLACEMENT

1. Disconnect battery
2. Disable Supplemental Restraint System (Airbags)
3. Remove traction control switch from rear of center console plate
4. Open console lid and remove screws at front of console
5. Pull console plate up to release clips and slide over shifter
6. Pull rearward to release clips retaining instrument panel accessory trim plate to instrument panel
7. Remove screws attaching radio to instrument panel
8. Disconnect electrical connectors and remove radio
9. Take down instrument panel hush panels and disconnect courtesy lights. Remove hush panels
10. Remove knee bolster and knee bolster bracket from driver's side below steering column
11. Remove screws from IPC trim plate
12. Pull out instrument panel cluster trim plate to release from retainers
13. Remove trip odometer and reset switch from IPC trim plate
14. Remove IPC trim plate
15. Remove screws from IPC and pull IPC out
16. Disconnect electrical connectors from IPC and remove IPC from the instrument panel
17. Disconnect ignition switch connectors
18. Turn ignition switch to the ACC position and remove park lock cable from ignition switch
19. Turn ignition switch to ON position
20. Depress and hold locking tab on right side of ignition switch with a small, flat-bladed screwdriver and pull ignition lock cylinder from ignition switch
21. Remove ignition switch bezel from ignition lock cylinder
22. Remove screws attaching ignition switch to bracket
23. Remove ignition switch through the IPC opening
24. To install, reverse procedure

Apr 04, 2011 | 1999 Oldsmobile Intrigue

1 Answer

The driver's side window in my 2000 Oldsmobile Intrigue has retracted into the door and I cannot get it to return to the normal position. The other windows will go down and up on command. What could the...


The easiest thing to try is to push the button for the window to come up and while holding it, bang the inside of the door and sometimes this will free the window and it will move up. If not it could be a problem with the wiring or motor and you will have to get it check out by a tech.

Jan 26, 2011 | Oldsmobile Intrigue Cars & Trucks

1 Answer

How do i remove the rear seat in a 2000 oldsmobile intrigue


A hard pull from the front edge should release two clips holding it down.

Dec 31, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Driver side window won't go up or down


Sounds like your window regulator and cable has jammed or just gone bad. Needs replacement as a whole. Regulator that is.

Nov 30, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Turn signal blinker problem. They work properky


sounds like wiring.or there may be a plate in the steering wheel.the plate in the steering wheel seems more plausible because wiring on both sides is less likely.it wouldn't hurt to check the wiring as far as you can to the rears though.any brake lights work?

Jul 21, 2010 | 2000 Oldsmobile Intrigue

1 Answer

How to remove passenger side door panel, for 2000 Olds Intrigue?


1. Remove the door latch trim plate (coupe and sedan front doors).
2. Remove the ashtray (sedan rear doors).
3. Remove the seat belt retractor cover (coupe and sedan front doors). Use a suitable door trim panel removal tool to release the clip retainers
4. Remove the door lock trim plate and the power window switch, if so equipped.
5. Remove the window regulator handle by removing the inner retaining clip, if so equipped.
6. Remove the remote mirror control, if so equipped
7. Remove the trim panel retaining screws
8. Remove the door trim panel using a door trim panel removing to work loose the retainer clips.
9. Detach all electrical and remote mirror controls, as required.

To install:

10. Install the wiring harnesses through the openings in the panel, as equipped.
11. Position the trim panel to the door and align the clips. Press the trim panel to the door until all the clips are fully engaged. Align all the holes before engaging the clips.
12. Install the screws, remote mirror control and inside door handle bezel, as equipped.
13. Install the window regulator handle or power window switch.
14. Install the door trim plate, seat belt retractor cover or ashtray.

Dec 04, 2017 | 2000 Oldsmobile Intrigue

1 Answer

Power windows don't work, looking for fuse box


There's two - one under the hood, the other on the end of the dash on the far right, the passenger's side, between the dash and the door panel (when the door is closed).

Mar 23, 2010 | 2000 Oldsmobile Intrigue

1 Answer

My driver side window wont go back up I think the wire inside is loose that pull the window up or down


if you can't hear the motor , try this hold the button in the up position and slap the door with your open hand from the inside . if this works ? leave the window up till you can get the motor repaired or replaced (worn motor brushes)..was i help ? leave feedback . thnks Jay

Feb 16, 2010 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

400 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...