Question about 2000 Ford Focus

1 Answer

Need diagram for timming mark set up to install belt

2000 focus with single cam installed new head need diagram for timming belt

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 70 Answers

Here ya go, need diagram for timming mark set up to install be - 84775161

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a ford focus timing marks single overhead cam diagram


depending on trans and engine mount type the mark my be on flywheel but generally most cars it is located on the belt pulley attached to crank rod, center bottom one on engine block. the timeing mark should be visable from top looking down. if you use a big ratchet to turn over the engine by hand and go slowly, you should see thhe marks pass as you do so.

Aug 14, 2014 | 2002 Ford SVT Focus

1 Answer

Timing Diagram of 2000 Ford Focouse DOHC 2.0 Zetec


If you Blew off the timing belt then need Head work also since it is an interference Motor
meaning that the Valve train and Pistons Have no Clearance so U are going to need a lot more work than just a timing belt to run

Mar 31, 2014 | 2000 Ford Focus

1 Answer

Need a DIAGRAM FOR A FORD ESCORT 1999 TIMING MARKS


2.0 single over head cam ?

airjer995.gif

2.0 DOHC you'll need the tools to lock the cams and crankshaft in place before you install the timing belt.

Jan 23, 2011 | 1999 Ford Escort

1 Answer

Hey guys I need to get changed the timming belt on my hyundai accent 1995 and I can do it myself but don´t have the timming marks diagram, can you please help me?


if its a single cam the marks should be on the backing plate and if it is twin cam the two marks should face each other on the compression stroke of the number 1 cylinder and the same goes for single cams line the mark up with the backing plate in the compression stroke of number 1 cylinder.

May 27, 2010 | 2001 Hyundai Accent

2 Answers

Diagram for timming belt on 2002 ford focus 2.0ltr


there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Jan 23, 2010 | 2002 Ford SVT Focus

1 Answer

Can not find timming marks on cam gears


Ther are none. It takes a tool to hold the cams in place while the valve cover is removed. Get a chilton book from the library.

Nov 03, 2009 | 2001 Ford Focus

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

2 Answers

I need a diagram to sincronize the timing belt of my isuzu tropper 3.2 sohc


if this is 6VD1 engine it has single cam gear each head, but is still a 2 cams per head, engine
if belt has broke or you have turned any gear you must remove rocker covers to check positions of camshafts front lobes are in certain spot as well as timming mark on belt driven cam gear to cover
this cam gear is a 3:1 ratio (3 turns of cam gear = 1 turn of cams)
184d763.jpg

Jun 12, 2009 | 1993 Isuzu Trooper

1 Answer

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times this causes pump o ring seal to leak if turning.

May 19, 2009 | 2000 Daewoo Lanos

1 Answer

Cannt find tims marks on 2000 ford focus twin cam


there are no marks on the cams line the crank up you should see marks on it and on the cams take a flat piece of steel like a flat file and put it on the end of the cam shafts the side near near the drivers side ounce you take a look youll see what i mean this should help you out

May 10, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...