Question about 1994 Toyota Camry

1 Answer

How does the crankshaft pulley get reinstalled..the outer pulley just came off when we were changing the belt

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

Your going to have to purchase a new pulley. Unfortunately, it separated on you or you may have damaged it when pulling it off.

Posted on May 30, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2002 Answers

SOURCE: The outer ring on the crankshaft pulley slipped

You need to replace the harmonic balancer. That is the part that is causing your problem. It attachs to the crankshaft and is made of 2 pieces of steel connected with a piece of rubber. It is all bonded together so if it comes apart the only fix is to replace it. You should be able to get a new one at your autoparts store or a used one at a scrap yard.
You will need a special puller to get it off. You can get it at the auto parts store for about $35-$45. It looks like a Y with an extra leg and comes with an assortment of bolts. You may also be able to rent or borrow it there. Some auto parts store have tools that you can use when you buy the parts there. The inner part of the balancer will have bolt holes where the puller fastens.Fasten it on and turn the center bolt inuntil it's tight. If the balancer doesn't want to move then give the center bolt a sharp rap with a hammer and tighten some more. Repeat if necessary. Clean off the crank with some emery cloth before you put the new balancer on and tighten the bolts. A couple hours should have you back on the road. Hope this helps.

Posted on Mar 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the belt on my van keep coming off or breaking/stripping off?


Check the harmonic balancer. That is the the pulley that is attached to the crankshaft. The outer ring of the pulley, where the belt rides, is pressed onto the hub of the pulley and isolated from it by a rubber bushing that separates the outer ring (belt pulley) from the inner part that is attached to the crankshaft. The rubber will dry out and shrink as it ages and the outer ring will slide in or out (front or back), causing belt misalignment. This can cause stripping and jumping off as it doesn't provide the proper path for the belt. The new balancer is fairly easy to install, and they only cost about $60.00 USD. You need a harmonic balancer puller to remove it, but most auto parts stores will provide a loaner for the DIYer. Here is a picture of the one that goes on your Montana.....



26204154-wk14e02lxnvxg33ug1vliqgq-1-0.jpg

May 25, 2016 | 2003 Pontiac Montana

1 Answer

How do you remove the crankshaft dumper pully?


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

Jan 27, 2016 | 2006 Land Rover Range Rover Sport

1 Answer

I have a 91 taurus Sho I changed the alternator and put new belts on now the belts won't line up right so I bought a 4 rib instead of the original 6 rib belt for the alt belt and it's smaller so it isn't...


Check the crankshaft pulley, it may be walking out due the rubber vibration sandwich being deteriorated between the inner and outer ring. Pull the wheel house to access it.

Mar 24, 2014 | Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

Can you tell me where I can print instructions for free to help me change my timing belt in a 93 ford festiva


Here are the instructions for removing the timing cover, and for replacing the timing belt. If this is helpful, please click my accept button! Thanks!
Remove accessory drive belts.
  1. Remove water pump pulley to pump hub attaching bolts, then the pulley.
  2. Remove right inner fender panel to gain access to crankshaft pulley.
  3. Remove outer crankshaft pulley attaching bolts, then the outer stiffener/spacer and outer pulley
  4. Remove inner stiffener/spacer, attaching screws, inner pulley and baffle plate.
  5. Remove attaching bolts, then the upper and lower timing covers.
  6. Reverse procedure to install. When installing crankshaft pulley, ensure curved lip on baffle plate and deep recess of inner pulley face outward

8fb9fc4.gif
  1. Remove timing belt covers as outlined previously.
  2. Remove timing belt tensioner pulley attaching bolt, then the tensioner pulley, spring and spring cover
  3. If reusing old belt, mark direction of rotation on belt to aid installation.
  4. Remove timing belt from crankshaft and camshaft sprockets.
  5. Check crankshaft and camshaft sprockets, tensioner pulley and timing belt for wear or damage. Replace components as necessary.
  6. Align camshaft and crankshaft sprocket timing marks with marks on cylinder head and oil pump housing
  7. Install timing belt. If reusing old belt, ensure belt is installed so that direction of rotation mark made during removal is positioned correctly.
  8. Install spring and spring cover onto tensioner pulley, then install pulley and attaching bolt. Do not tighten bolt at this time.
  9. Install tensioner spring onto anchor, then tighten pulley attaching bolt to torque listed at the end of this section.
  10. Reinstall timing belt covers.

spacer.gif 2006-05-25_081817_fest2.thumb.gif
This photo shows timing marks.


59f76eb.gif

Jul 14, 2010 | 1993 Ford Festiva

1 Answer

Timing belt markings mazda B2500 1998


Timing Belt, Sprockets & Front Cover Removal & Installation Timing belt To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the exhaust side spark plugs, outer timing belt cover, and crankshaft pulley.
  3. Turn the crankshaft until the number one piston is at top dead center (TDC). CAUTION
    The camshaft belt tensioner tool (303-097) can be damaged when trying to relieve belt tension if you attempt to remove the belt without first loosening both the timing belt tensioner adjusting bolt and the spring pivot bolt.
  4. Loosen the timing belt spring pivot bolt, but do not remove it at this point in the procedure.
  5. Loosen the adjusting bolt slowly and release the spring tension.
  6. Turn the tensioner with the camshaft belt tensioner tool (303-097), against the spring pressure, clockwise to the farthest position.
  7. While holding it in this position, tighten the adjusting bolt to hold the tensioner away from the belt.
  8. Remove the timing belt.
To Install:
  1. Be certain that on piston number one, the crankshaft is at TDC with the crankshaft keyway pointing straight up and the circle on the crankshaft sprocket lined up with the notch on the engine front cover.
  2. Line up the timing marks.
  3. Install the timing belt over the crankshaft sprocket going counterclockwise over the oil pump sprocket and over the camshaft sprocket.
  4. Loosen the bolt allowing the tensioner pulley to press against the timing belt. NOTE: The timing belt tensioner should not be tightened or the belt tension will not be evenly distributed over the whole belt.
  5. Turn the crankshaft two revolutions clockwise. Next, slowly bring the crank to the number one position firing position with the keyway on the crank facing up. The dot on the crankshaft gear is lined up with the notch on the front cover.
  6. Check the timing mark alignment again. If necessary, repeat the procedure.
  7. Tighten the bolts. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  8. Install the crankshaft pulley and tighten the bolt. Torque to 93-121 ft-lb (125-165 Nm).
  9. Install the outer timing belt cover and tighten the bolt. Torque to 70-106 in-lb (8-12 Nm).
  10. Install the exhaust side spark plugs.
Sprockets To Remove:
  1. Remove the timing belt.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the sprocket.
  3. Remove the camshaft sprocket.
To Install:
  1. Place the key and camshaft sprocket on the shaft.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the camshaft sprocket and tighten the bolt. Torque to 52-70 ft-lb (70-95 Nm).
  3. Remove the tool then install the timing belt.
Outer Cover To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the fan shroud.
  4. Loosen the bolts on the water pump pulley, but do not remove them at this point in the procedure.
  5. Remove the drive belt, the water pump pulley, and the fan and clutch assembly.
  6. Recover the refrigerant from the A/C system.
  7. Disconnect the A/C wiring connector.
  8. Remove the A/C compressor from the mounting bracket then remove the A/C mounting bracket with the power steering pump still attached.
  9. Remove the outer timing belt cover.
To Install:
  1. Install the outer timing belt cover. Torque to 70-106 in-lb (8-12 Nm).
  2. Install the A/C mounting bracket with the power steering pump still attached. Torque the M10 bolts and stud to 35 ft-lb (48 Nm) and torque the M8 bolt to 18 ft-lb (25 Nm).
  3. Install the A/C compressor to the mounting bracket. Torque to 16-20 ft-lb (21-28 Nm).
  4. Connect the A/C wiring connector.
  5. Refill the refrigerant into the A/C system.
  6. Install the fan and clutch assembly, the water pump pulley, and the drive belt.
  7. Tighten the bolts on the water pump pulley. Torque to 13-17 ft-lb (17-23 Nm).
  8. Install the fan shroud. Torque to 54-70 in-lb (6-8 Nm).
  9. Connect the negative battery cable.
  10. Start the engine. Check for leaks and repair as necessary.
Inner Cover To Remove:
  1. Loosen oil pump sprocket bolt.
  2. Remove timing belt, timing belt tensioner, oil pump sprocket, and crankshaft pulley.
  3. Remove inner timing belt cover.
To Install:
  1. Install inner timing belt cover.
  2. Install crankshaft pulley. Torque to 93-121 ft-lb (125-165 Nm).
  3. Install the oil pump sprocket.
  4. Install the timing belt tensioner. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  5. Install the timing belt.
  6. Tighten the oil pump sprocket bolt. Torque to 30-40 ft-lb (40-55 Nm).
  7. Torque the camshaft bolt to 52-70 ft-lb (70-95 Nm).

Jul 12, 2010 | 1998 Mazda Pickup

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

1 Answer

Serpentine belt


5729dde.gif
This is a job for an experienced technician. Probably about a $300 job. Maybe more.

Here is procedure for 1996:

Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301).
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592).
  1. Remove the main wiring harness from the upper engine front cover (6019).
  1. Remove the eight upper engine front cover bolts and the upper engine front cover.
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775).
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501).
  1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover.
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
2acab54.gif
18. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.

If the timing chain/belt is to be reused, mark the direction of rotation on the timing chain/belt.

19. Loosen the timing chain/belt tensioner nut.

  1. Remove the timing chain/belt.
Installation
NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned.



stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Pay special attention to the tooth shape of the timing belt. The current timing belts are not interchangeable with the timing belts from the 1993 model year. The 1993 model year uses a square or trapezoidal tooth timing belt while the current model year uses a rounded tooth design. The design change was made to extend the service life of the timing belt from 60,000 miles for the square or trapezoidal toothed belt to 105,000 miles for the rounded tooth belt. If the proper timing belt is not used, the customer may complain of a "whining" noise coming from the engine compartment. If the camshaft sprocket has a square cut in the valley of the gear tooth, it will require a square or trapezoidal tooth timing belt. If the camshaft sprocket has a rounded cut in the valley of the gear tooth, it will require a rounded tooth timing belt.
NOTE: If a new timing chain/belt is to be installed, make sure that the arrow is pointing away from the engine. If a timing chain/belt is to be reused, make sure that the directional arrow that was marked during disassembly is facing the correct direction.

NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts and the crankshaft. These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket.

NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600).

Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprockets following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner.

  1. While holding the timing chain/belt tensioner with an Allen wrench, loosen the timing chain/belt tensioner nut.
  1. Allow the timing chain/belt tensioner to put pressure on the timing chain/belt.
  1. Use an Allen wrench to turn the timing chain/belt tensioner 70-80 degrees clockwise and tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).

    1. Rotate the crankshaft (6303) clockwise twice and align the No. 1 piston to Top Dead Center (TDC) on its compression stroke.
    1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear camshaft sprocket and the timing chain/belt tensioner.
    2. NOTE: An assistant may be needed to adjust the timing chain/belt.

      While holding the timing chain/belt tensioner steady with an Allen wrench, loosen the timing chain/belt tensioner nut. Remove the Allen wrench and adjust the timing chain/belt tensioner as follows:
      1. Install a 0.35mm (0.0138 inch) thick and 12.7mm (0.500 inch) wide feeler gauge as shown.

  1. Turn the crankshaft clockwise to position the feeler gauge between the timing chain/belt tensioner and the timing chain/belt

  1. Tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).
  1. Turn the crankshaft clockwise to remove the feeler gauge from between the timing chain/belt tensioner and the timing chain/belt.
  1. Rotate the crankshaft clockwise twice and align the No. 1 piston to TDC on its compression stroke.
  1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear and front camshaft sprocket.
    1. Measure the timing chain/belt deflection. Timing chain/belt deflection should be between 13-15mm (0.51-0.59 inch). If timing chain/belt deflection is not within specification, repeat steps 3-11. If the timing chain/belt cannot be adjusted to within specification, the timing chain/belt will have to be replaced.
    1. Position the lower engine front cover and install the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
    1. Install the outer timing chain/belt guide and the crankshaft pulley. Refer to the procedure in this section.
    1. Position the water pump pulley on the water pump and install the four water pump pulley bolts
    1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
    1. Position the RH outer engine and transmission splash shield and install the four RH outer engine and transmission splash shield bolts and two screws.
    1. Install the RH front wheel and tire assembly. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).



Feb 14, 2009 | 1993 Mercury Villager

1 Answer

Inner crankshaft pulley moves 1/4 '' in and out


i think you need a new harmonic balancer. good luck.

Nov 23, 2008 | 1996 Toyota Tercel

1 Answer

1994 saab 900 se replacing timing belt


STEP 1 Remove Air Filter. STEP 2 Loosen the bolts securing the crankshaft pulley. Remove the load from the belt tensioner by turning the belt tensioner pulley locking bolt forward in the car using a 15 mm wrench. Remove the belt from the coolant pump pulley and slowly release the belt tensioner. STEP 3 Remove the belt tensioner and remove the steering pump pulley STEP 4 Remove the water pump pulley use the engine bracket to pry against. STEP 5 Remove the timing cover and Remove the right-hand front wheel and the cover in the wheel housing. STEP 6 Remove the crankshaft pulley (undo the six bolts but do not remove the centre bolt). STEP 7 Place the engine top dead center and Zero the engine. The markings on the camshaft sprockets and timing cover should be in alignment as also should the marking on the crankshaft. Use locking tools 83 95 006 and KM-800-2 for the camshaft sprockets and locking tool KM-800-10 for the crankshaft (These tools can be purchased from Saab (18774177222) or from Baum Tools). STEP 8 Before removing the toothed belt mark its direction of rotation . To facilitate refitting the belt can be marked at both the camshaft marking and the crankshaft marking. STE9cc7b85.jpgP 9
STEP 10 Fit the toothed belt according to the marked direction of rotation. Use setting tool 83 95 006 to keep the belt in place and adjust the tensioning roller loosely by hand to prevent the belt from jumping off. Adjust counterclockwise. Fit a section of the toothed belt and fit tool 83 93 985 to measure the belt tension. Loosely tighten the centre bolts of the adjusting rollers. Adjust the lower adjusting roller counter clockwise to a belt tension of 275-300 Nm. Turning torque 30 lb.ft ft ******The adjustment of the belt tension is for preparation ONLY and must not be used as a check when the belt adjusted for the final time! STEP 11 Turn the engine over two revolutions until just before the zero mark and place the locking tool on the crankshaft. Carefully turn the crankshaft in the direction of engine rotation until the arm rests against the coolant pump's flange and then tighten the arm. Fit setting tool 8395006 and check that the markings on the camshaft sprockets are aligned with the markings in the tool. ********Check that the A marking is approximately 2mm above B marking. If the distance is less readjustment is necessary. STEP 12 Fit the crankshaft pulley and Tighten to a torque of 15 foot lbs. STEP 13 Reinstall the inner wheel cover and front right wheel.
STEP 14 Reinstall Timing Cover.
STEP 15 Reinstall the water pump pulley use the engine bracket for leverage. STEP 16 Reinstall the power steering pulley and tighten to 6 foot lbs. STEP 17 Reinstall the belt tensioner and tighten to 30 foot lbs. STEP 18 Remove the belt tensioner load/pressure by turning the belt tensioner pulley locking bolt forwards in the car using a 15 mm wrench. Install the belt on the coolant pump pulley. Carefully release the belt tensioner. STEP 19 Reinstall the Air Cleaner and hoses that accompany Release the belt tension and remove the toothed belt.

Jul 18, 2008 | 1994 Saab 900

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...